Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Montclair, CA MODEL SEF36 ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS AND OWNER’S MANUAL SAFETY INFORMATION When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, property damage, electric shock, and personal injury. • Read all instructions before using this unit. • This heater may be hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains, at least 3 feet from the front of the heater and keep them away from the sides and the rear. • Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended. • If a new circuit or outlet is required for this log set, wiring should be done by a qualified electrician. • Always unplug the heater when not in use. • Follow all local codes, including the use of ground fault protection, where required. • Use properly fused outlets. • Do not modify this heater or use it in any manner not recommended by the manufacturer. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. • Do not use this heater outdoors, in bathrooms, laundry rooms, or damp basements, or in any other area where moisture may be present. Never locate the heater where it may fall into a bathtub. • Do not operate this heater if the power cord is frayed or damaged, if the plug is damaged, or if the heater itself has been dropped or damaged or has malfunctioned. Contact your local dealer or Empire. • Do not run the power cord under carpeting, throw rugs, or runners. Position the cord away from traffic areas so it cannot trip anyone. • To disconnect the heater, turn controls to off, then remove the plug from the outlet. • Avoid the use of an extension cord because the it may overheat and cause a risk of fire. If an extension cord must be used, it shall be No. 14 AWG minimum size and rated not less than 1875 watts. • Keep foreign objects and fingers away from the blower inlet and outlet as this may cause an P/N 140599 1 ver. 11/2002 • Do not burn wood or other material in this fireplace. • Unplug the power cord before performing any cleaning or maintenance to the heater or before moving it. The SEF package contains one fireplace assembly; two light bulbs; one flame package containing one flame assembly and three film strips for flames; one log package containing one front log, one rear log and three top logs; and this manual. NOTE: A15 Amp, 120 Volt circuit is required. A dedicated circuit is preferred but not essential in all cases. A dedicated circuit will be required if, after installation, the circuit breaker trips or fuse blows on a regular basis when the heater is operating. Additional appliances on the same circuit may exceed the current rating of the circuit breaker. CLEARANCES AND PREPARATION This fireplace has the following dimensions: Maximum Width- 36” Maximum Depth -13 1/16” Height -26 7/8”. (See Figure 1) There are no combustion or heat restrictions on this fireplace. It can be installed in any space into which it will fit, provided the area meets the requirements listed under IMPORTANT INSTRUCTIONS above. This fireplace does NOT require venting. The fireplace should rest on a flat, solid surface. This fireplace comes completely wired. It requires only to be plugged into a 15 Amp, 120 Volt circuit. It is best if the outlet is located so it can be reached with the 8 ft. power cord. However, an extension cord may be used, provided it is rated at not less than 1875 watts. There are two options for installing the SEF: 1. Set the unit against the wall. Space requirements are simply the dimensions of the fireplace (36” x 13 1/16” x 36 7/8”). 2. Frame the unit in. Combustible materials can be brought right up to the fireplace. However, for ease of installation it might be best to leave 1/8” clearance around the fireplace (framing dimensions of 36 1/8”W x 27”H x 13 3/16"D). INSTALLATION 1. Remove the fireplace from its shipping carton. Remove the log package, light bulbs, flame strip package, and all packaging materials from the cabinet of the fireplace. 2. Uncoil the power cord, but do NOT plug in the cord at this time. Set the fireplace in its final position. Establish the path to the outlet for the power cord. The cord should run as close to the wall as possible and be out of the way of traffic. WARNING: To reduce the risk of fire, property damage, electric shock, and personal injury, the cord must not be pinched or pressed against a sharp edge. Do not rout the cord under carpeting or throw rugs. P/N 140599 2 ver. 11/2002 3. Install the light bulbs into the light sockets. Hold the sockets while installing the bulbs to prevent twisting. Figure 2 Comer Dimensions (Excluding Mantel) Cabinet Dimensions Figure 1 4. Remove the logs from their packaging. Install the front and rear lo...