With zone heating, you save 3% on your energy bill for every 1°-thermostat set-back. That’s 15% for every 5°! Your savings can total $312* annually. * Cost savings based on a 5° thermostat set-back. Calculations established on average natural gas/propane heating costs published by U.S. Department of Energy. Gas is still a better value than wood or electricity! $0.37$0.61$0.83$0.94Ideal for any season, new LED flame. Approved for use in any room of the home. Easy operation -Great value --Unparall

7. Attach the two mounting brackets to blower housing using four screws provided in blower kit (2 for each bracket) (see Figure 16, page 13). Tighten screws securely. Place blower assembly temporarily on top of firebox. 8. Working from the rear of the stove, place entire power cord, including speed control housing, in lower control compartment. 9. Route ends of 3-wire power cord up from the lower control compartment through the plastic bushing, then up to the upper cavity of stove (see Figure 17

Burner orifice clogged 2. Inlet gas pressure is too low 3. Thermopile leads disconnected or improperly connected 4. Burners will not come on in remote position 1. Clean burner (see Cleaning and Maintenance, pages 16 and 17) or replace burner orifice 2. Contact local gas company 3. Reconnect leads (see wiring diagram) 4. Replace battery in transmitter and receiver Delayed ignition burner 1. Manifold pressure is too low 2. Burner orifice clogged 1. Contact local gas company 2. Clean burner (see Cl

Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream from heater (see Figure 21). Apply pipe joint sealant lightly to male threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged heater valves. CAUTION: Use only new, black iron or steel pipe. Inter- nally-tinned copper tubing may be used in certain areas. Check your local codes. Use pipe of 1/2" or greater diameter to allow proper gas volume to heater. If pipe is too

• As a visual effect - only the flame effect is on, the heater is off. We recommend this mode for warm weather application, when you want the ambiance of a fire, without any heat output. The log set control functions can be accessed in two (2) ways: • Using the control panel buttons, located on the lower right-hand corner of the log set. • Using the multifunction remote control unit. Figure 3 1 2 3 3 2 1 Main Power Button: This button supplies power to all the functions of the log set. The Main

EST, Monday – Friday. 20-10-105 Rev. 6/11 C US INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. WARNING! IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, AN ELECTRICAL SHOCK OR FIRE MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. IMPORTANT INSTRUCTIONS PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING APPLIANCE TABLE OF CONTENTS Safety Information ..................................................................

Feed flexible gas line into fireplace base area while replacing log base assembly. Make sure the entire flexible gas line is in fireplace base area. Reattach log base assembly to fireplace with screws removed in step 2. CHECKING GAS CONNECTIONS WARNING: Test all gas piping and connections for leaks after installing or servicing. Correct all leaks at once. WARNING: Never use an open flame to check for a leak. Apply a mixture of liquid soap and water to all joints. Bubbles forming show a leak. Cor

GLASS DOOR Glass must be cleaned periodically. During start-up it is normal for condensation to form on the inside of the glass causing lint, dust, and other airborne particles to cling to the glass surface. During initial start-up a slight film may form on the glass due to paint curing. The glass should be cleaned several times with a non-amonia, nonabrasive household cleaner and warm water after the first two weeks of operation. Thereafter, clean the glass two or three times during each heatin

Check your building codes for any special requirements for locating manual shutoff valve to fireplaces. Apply pipe joint sealant lightly to male threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged fireplace valves. We recommend that you install a sediment trap/drip leg in supply line as shown in Figure 35. Locate sediment trap/drip leg where it is within reach for cleaning. Install in piping system between fuel supply and heater. Locate

Apply a bead of non-hardening mastic around the outside edge of the vent cap. Position the vent cap in the center of the 7 1/2" or 10" hole on the exterior wall with the arrow on the vent cap pointing up. Insure proper clearance of 1" to combustibles is maintained. Attach the vent cap with four wood screws supplied (see Figure 13). Note: Replace the wood screws with appropriate fasteners for stucco, brick, concrete, or other types of siding. WARNING: Do not recess vent termination in to any wall