Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
AC voltage selector switch Fig. 1 Before plugging in this unit, make sure that the position of the AC Voltage Selector conforms to your line (mains) voltage. If not, it must be reset. See Fig. 1. WARNING NOTICE: IN MOST CASES IT IS AN INFRINGEMENT OF COPYRIGHT TO MAKE COPIES OF TAPES OR DISCS WITHOUT THE PERMISSION OF THE COPYRIGHT OWNERS. ANYONE WISHING TO COpy COMMERCIALLY AVAILABLE TAPES OR DISCS SHOULD CONTACT THE MECHANICAL COPYRIGHT PROTECTION SOCIETY LIMITED OR THE PERFORMING RIGHTS SOCIETY LIMITED. Precautions for use To maintain the high performance and reliability of this unit, avoid using or storing it in the following conditions. • Dusty places. • Near heat sources such as stoves, etc. • Condensation (dew) • Places exposed to direct sunlight, especially in a closed car. • Extremely cold places. • In moist, humid locations or when the room temperature rises quickly such as right after turning on a heater, condensation may form inside the unit, preventing the unit from operating normally. If this occurs, remove the tape and let the unit sit with the cassette holder open for approximately two hours before use. (The entire display area blinks to warn you that there is condensation inside the unit.) • Using headphones • DAT players have such a low noise level that listeners often tend to overly increase the sound volume. Set the sound volume to an appropriate level to protect your ears from excessive shock. • For your safety and the safety of others, do not use headphones while driving a car or other type of vehicle. • Be careful not to fall asleep while listening to music using headphones. • Continuous use of headphones for long periods may hurt your ears. DX-7 3 Use of OAT cassette tapes • Tapes cannot be turned over and played on the other side. • Tapes are manufactured with a sealed construction. Do not try to forcefully open the tape cover or pull the tape from the case, and never attempt to disassemble the tape case. • Do not repeatedly insert and remove a tape without playing or recording the tape. The tape may become slack or damaged. • After use, completely rewind the tape and store it properly. The tape may be damaged if stored without being fully rewound. • Always place a tape in its case for storing . • Accidental erasure prevention side door 4 DX-7 To prevent accidental erasure Re-recording • OAT tape recording system Tape running direction PCM audio signals Subcode area DX-7 5 - ~ - • Using rechargeable batteries Use the separately sold AID converter (BP-A7). • Align the AID converter with the main unit's accessory attachment guide hole and attach. Secure the AID converter in place using the accessory attachment screw. • Always turn the [POWER] switch OFF before inserting/removing batteries or making connections. • Paying close attention to match the insertion direction with the arrows, insert two NB-8 rechargeable battery packs (supplied in the BP-A7 kit) into the AID converter/battery pack unit supplied in the BP-A7 kit. • Recharging period: When the batteries run down, "Lo" appears in the display area to indicate that operation will soon stop. Recharge the batteries at this time for continued operation. • For maximum battery life: One characteristic of Ni-Cd batteries is that their battery life becomes shorter if they are repeatedly recharged before being completely used up. If this occurs, battery life can be returned to normal by repeatedly letting the batteries completely run down before recharging. OX-7 9 IO-'~ol ~ _ " ___________ ~___________________________ • Connection for analog recording Use the separately sold AID converter (BP-A7). • Turn off the power to both the amplifier and this unit before making connections. • Connect the AID converter unit (supplied in the BP-A71 to this unit. • Connect the AID converter unit's [MIC/LINE IN] jack to an amplifier's [TAPE REC] jacks or a stereo microphone. • Connect the AID converter unit's [LINE OUT] jack to an amplifier's external input jacks (AUX jacks, TAPE PLAY jacks, etc.). Both input and output connections should be made with the red plug connected to the amplifier's "R" (right channell jack and the white plug connected to the "L" (left channell jack. • Use the AID converter unit's [MIC/LlNE] switch to MIC or LINE, depending on the connection. • Adjust the playback sound volume using the amplifier's volume control. • When using a microphone, use a stereo microphone equipped with a 3.5 mm diameter stereo miniplug. If you use a monaural microphone, the sound will be recorded on the left channel only. REC ouT PLAY BACK 1i:J\ @@ r~H-I------d Stereo microphone~~hite ~.. _=:J J ~~~'\~MIG/LINE IN -====") Separately sold BP-A7 DX-7 13 " ~ " ~" " ~ " " Digital recording First load a tape into the unit (see page 14). Operation is possible with either the main unit or the remote controller. ""LILI ~II .- 11.1111 U'LILI rl I ST·ID mill • LI I 11.11 -, ULI :J 18 DX-7 Connect the unit (See page 11.) • Press the [REC] button. When starting re...