Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
This allows for precise dispensing of various flavors of products. Programming of the dispenser is achieved by entering a certain function, then, by use of programming switches, the operator can customize the dispensing process to their specifications. To access the programming mode, and to scroll through different function screens, the programming switches shown are used. There are five switches that will be used for setup of the dispenser. A. Enter program mode and advance to next menu B. Increment display value positive C. Exit program mode D. Increment display value negative C. Return to previous menu E D C B A Using the menu-driven display (TOUCH SCREEN) on the front of dispenser, the operator has the ability to alter or modify various functions of the dispenser. This allows for precise dispensing of various flavors of products. Programming of dispenser is achieved by entering a certain function, then, by use of programming switches, the operator can customize the dispensing process to their specifications. To access the programming mode, and to scroll through different function screens, the programming switches shown are used. There are five switches that will be used for setup of the dispenser. 45304.1 090611 PROGRAMMING THE DISPENSER (Cont.) GLOSSARY Put "NORMAL/PROGRAM/RINSE" switch into "PROGRAM" position to access program menus. Enables lockout of dispensing if below minimum water temperature Adjust tank temperature (190° F maximum) TANK TEMP ###° DISPENSE LOCKOUT (-) EXIT (+) NO EXIT YES Enables rinse alarm Adjust minimum tank ready temperature for lockout (185° maximum) RINSE ALARM ? READY TEMP ###° NO EXIT YES (-) EXIT (+) Turns on audio alarm Adjust hopper motor speed for hopper 1. ## indicates hopper rpm AUDIBLE ALARM? DRINK STRENGTH 1 NO EXIT YES (-) ## (+) Enables service number to be displayed on door display If password is set, requires entering password to access remainder of menus ENABLE SERVICE # ENTER PASSWORD NO EXIT YES (-) 0 (+) Enter asset number of machine Calibrate temperature probe ENTER ASSET # ? ###° CAL ###° NO EXIT YES (-) tank temp (+) Set refill probe threshold Enables service agent telephone number to be displayed on door display 235 REFILL 155 ENABLE SERVICE # (-) EXIT (+) NO EXIT YES Runs auger motor (1 thru 6) at programmed speed for 10 seconds to check throw rate Allows testing of dispense switches TEST POWDER #? TEST SWITCHES ? PRESS DISPENSE Use Switch To Test Opens water dispense valve (1 thru 4) for 20 seconds to test flow rate Allows manually activating tank heater TEST WATER #? TEST HEATER ? PRESS DISPENSE EXIT YES Set delay start of hopper after dilution valve opens in station selected AUGER DELAY Allows manually activating refill valve TEST REFILL ? (-) .## sec (+) EXIT YES Set delay start of dilution water valve for single product beverages DILUTION DELAY Allows manually activating hot water valve TEST HOT WATER ? (-) #.## sec (+) EXIT YES Set low powder detect threshold Allows manually activating hopper motors ### POWDER 155 TEST AUGERS ? (-) EXIT (+) DISPENSE TO TEST Set number of Auger turns after low level detected until hopper empty SET TO EMPTY Allows manually activating whipper motors TEST WHIPPERS ? (-) 100 REVS (+) DISPENSE TO TEST Allows manually activating dispense valves Allows password to be set to prevent altering setup functions TEST DISP VALVES SET PASSWORD ? DISPENSE TO TEST NO EXIT YES 45304.1 090611 PROGRAMMING THE DISPENSER (Cont.) Press and release right switch (advance to next screen), "TANK TEMP ###°" appears on screen. Adjust tank temperature CALIBRATION ? TANK TEMP ###° EXIT YES (-) EXIT (+) continue to A (B) LOCKS/DISABLES ? Adjust minimum tank ready temperature for lockout READY TEMP ###° EXIT YES (-) EXIT (+) continue to C (D) AUDIBLE ALARM ? DRINK STRENGTH 1 NO EXIT YES (-) ### (+) ENTER ASSET # ? DRINK STRENGTH 2 EXIT YES (-) ### (+) ENABLE SERVICE # DRINK STRENGTH 3 NO EXIT YES (-) ### (+) DIAGNOSTICS ? Repeat for drinks 4 through 6 EXIT YES (A) ENTER PASSWORD continue to E (F) (-) 0 (+) FACTORY DEFAULTS NO YES FINISHED, returns to main screen 45304.1 090611 PROGRAMMING THE DISPENSER (Cont.) (A) SELECT UNITS ENG EXIT METRIC TEST WATER 2? ###° CAL ###° TEST POWDER 6? (-) TANK TEMP (+) PRESS DISPENSE PRESS DISPENSE TEST POWDER 3? 0 REFILL 155 AUGER DELAY (-) EXIT (+) PRESS DISPENSE (-) #.## (+) TEST POWDER 1? TEST WATER 3? DILUTION DELAY PRESS DISPENSE PRESS DISPENSE (-) #.## (+) TEST POWDER 4? ## POWDER 155 TEST WATER 1? PRESS DISPENSE (-) EXIT (+) PRESS DISPENSE SET TO EMPTY TEST WATER 4? TEST POWDER 2? (-) 100 REVS (+) PRESS DISPENSE PRESS DISPENSE Return to (B) TEST POWDER 5? PRESS DISPENSE 45304.1 090611 PROGRAMMING THE DISPENSER (Cont.) (E) (C) DISPENSE LOCKOUT TEST SWITCHES NO EXIT YES Use Switch To Test RINSE ALARM ? TEST HEATER ? NO EXIT YES EXIT YES TEST REFILL ? RINSE ALARM TIME EXIT YES (-) ##HOURS (+) TEST HOT WATER ? RINSE LOCKOUT NO EXIT YES EXIT YES TEST AUGERS ? DISPENSE TO TEST SET PASSWORD ? (-) 0 (+) TEST WHI...