QTY. DESCRIPTION 20 27705.0000 1 Terminal Lug 02308.0000 1 Screw, Pan Head #8-32 x .375" 21 05746.0000 1 Bushing, Strain Relief 22 28004.0000 1 Switch, Heater ON/OFF (Includes 24) 23 25102.0001 1 Bracket, Switch Indicator/Guard 24 23696.0000 1 Facenut, Hex. 25 23697.0000 1 Facenut, Plastic 26 28051.0000 1 Wiring Harness, Main 240V 27946.0000 1 Wiring Harness, Main 240V W/Warmer) 27 12985.0003 1 Wiring Harness, Ready Light 28 25347.0000 1 Wiring Harness, Thermostat Not Illustrated 29 12919.0000 1

If continuity is present as described, reconnect the wires, the switch is operating properly. If continuity is not present as described, replace the switch. Removal and Replacement: 1. Remove all wires from the switch terminals. 2. Compress the clips inside the front of the housing and gently push the switch through the opening. 3. Push the new switch into the opening and spread the clips to retain the switch in the housing. 4. Refer to the following illustration when re- connecting the wires. 1

8. Repeat steps 4 thru 7 for the other hopper. APPROXIMATE TIMER SETTINGS IN SECONDS Weight Fine Drip Regular (ounces) (7*) (8*) (12*) 1.5 0.5 0.5 0.5 1.75 0.7 0.6 0.6 2.0 1.0 0.8 0.8 2.25 1.4 1.4 1.2 2.5 1.9 1.8 1.6 2.75 2.4 2.2 2.0 3.0 2.9 2.7 2.5 3.25 3.3 3.1 2.9 4.0 4.8 4.4 4.0 6.0 8.6 7.9 7.5 8.0 12.0 11.5 10.9 10.0 15.7 15.1 14.1 12.0 19.6 18.5 17.5 14.0 23.5 22.0 20.9 16.0 27.0 25.3 24.3 *Hash mark settings. Refer to Adjustment-Burrsection. TROUBLESHOOTING A troubleshooting guide is provi

Pot level, cold brew lock-out and tank temperature set easily from advanced touch pad on front of machine. Electronic diagnostics and built-in tank drain make service easier. Coffee controlled extraction with programmable pre-infusion and pulse brew. For current specification sheets and other information, go to Related Products Easy Clear® EQ-17-TL Product No. : 30200.1000 Dimensions: 127/16" H x 2V2" W x 3" D 31 .6 cm H x 6.35 cm W x 7.62 cm D Easy Clear® ED-17-TL Product No. : 30201.

. (Order Item 12) 7 -------------1 Bushing, Snap 1.188” Dia. (See Hood And Top Covers) 8 12364.0000 1 Decal, Warmers Are Hot 9 28382.0000 00908.0000 02332.0003 1 1 1 Clamp, Routing Nut, Hex #8-32 (Early Models) Screw, Hex-Crimptite #6-32 x . 375” (Late Models) 10 11 21016.0131 21016.0027 12985.0003 1 2 1 Lead, Electrical, Lower Warmers GRN/YEL 07” LG Lead, Electrical, GRN/YEL 26” LG Top Warmer Wiring Harness, One Lower, Two Upper Warmers, 230V Not Illustrated 12 04828.1001 -Tube, Silicone .250”

If continuity is present as described, proceed to #4. If continuity is not present as described, replace the switch. 4. Check for continuity across the .25" terminals of the switch when it is in the “ON” position. Continuity must not be present in the upper “OFF” position. If continuity is present as described, reconnect the wires, the switch is operating properly. If continuity is not present as described, replace the switch. Removal and Replacement: 1. Remove all wires from the switch terminal

USER NOTICES Carefully read and follow all notices on the grinder and in this manual. They were written for your protection. All notices on the grinder are to be kept in good condition. Replace any unreadable or damaged labels. KEEP FINGERS ANDFOREIGN OBJECTSOUT OF HOPPEROR CHUTE OPENING. PERSONAL INJURYHAZARD. #05876.0000 #37881.0000 #20545.0000 00824.0002 27091.1 040612 ELECTRICAL REQUIREMENTS The grinder has an attached cordset and requires 2-wire, grounded service rated 230 volts ac, 10 amp

The equipment is only for indoor use on a sturdy counter or shelf. Adequate space must be available above the grinder to raise the lid when adding beans. Use only with whole bean coffee. The grind is preset at the factory to drip specifications as set forth by the United States Department of Commerce and adopted by the Coffee Brewing Center of the Pan American Coffee Bureau. Adjustments may be made to alter both the amount and grind from the factory setting. USER NOTICES Carefully read and follo

6 RECTIFIER Location: The rectifier(s) is located inside on the right side of the stand housing just to the right of the transformer for 1SH Stand and on the right and left side of the stand housing for 2SH Stand. Test Procedures: 1. Disconnect the stand from the power source. 2. Remove the red wire and the black wire from the rectifier. 3. Check the voltage across the (+) and (-) terminals on the rectifier with a voltmeter. Connect the stand to the power source. The indication must be 24 volts