Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
6 Keurig_CareGuide_spreadsB70 5/17/06 1:06 AM Page 7 Keurig_CareGuide_spreadsB70 5/17/06 1:06 AM Page 7 Ready to Brew Your First Cup K-Cup® K-Cup Handle Chamber portion pack 1. LCD Control Center will indicate ‘READY TO BREW’. 2. Place a cup or mug on the Drip Tray Plate. 3. Lift the Handle and the K-Cup chamber will open toward you. CAUTION: There are two sharp needles that puncture the K-Cup® portion pack, one above the K-Cup Holder and the other in the bottom of the K-Cup Holder. To avoid risk of injury, do not put your fingers in the K-Cup Chamber. 4. Select a K-Cup® portion pack. NOTE: Do not remove the foil lid or puncture the K-Cup® portion pack. 5. Place a K-Cup® portion pack in the K-Cup Holder (as shown in exhibit at top of page). 6. Lower the Handle to close the Lid over the K-Cup Holder. (When it is closed completely, the LCD Control Center will indicate ‘READY TO BREW’. The ‘LEFT’ and ‘RIGHT’ Buttons will be lit and the ’BREW’ Button will flash up to 60 seconds.) a.All brew size icons are lit with the default size flashing. To choose a different size, press ‘LEFT’ Button to go down in size or ‘RIGHT’ Button to go up in size. NOTE: The small mug (7.25 oz. serving) is the factory set default brew size. To program your favorite brew size see page 11 “Programming Your Brew Size”. b. Your choices are a stronger small cup (5.25 oz. serving), a small mug (7.25 oz. serving), a large mug (9.25 oz. serving) or a travel mug (11.25 oz. serving). c. Once size is chosen, press ‘BREW’ Button. BREW Button will stop flashing, LEFT and RIGHT Buttons will no longer be lit and icon of brew size will be lit. NOTE: If you do not push the Brew Button in 60 seconds, the LCD Control Center will return to ’READY TO BREW’ and the Brew Buttons will be disabled to prevent accidental activation. Re-activate the Brew sequence by raising and lowering the Handle completely. 7. The LCD Control Center will now display the word ‘BREWING’ and the serving size you selected will be illuminated on LCD. CAUTION: There is extremely hot water in the K-Cup Holder during the brew process. To avoid risk of injury, do not lift the Handle or open the K-Cup Chamber during the brew process. 8. There may be a short pause before the brewing process begins. The process lasts about 60 seconds and ends with a burst of air to remove all liquid coffee or tea from the K-Cup. 9. Lift the Handle and remove and dispose of the used K-Cup. CAUTION: K-Cup will be hot. 10.Enjoy your first cup of Keurig Brewed® gourmet coffee or tea! 7 Keurig_CareGuide_spreadsB70 5/17/06 1:06 AM Page 8 Keurig_CareGuide_spreadsB70 5/17/06 1:06 AM Page 8 11. Your Brewer will display ‘NOT READY’ as it heats water for the next brew cycle. The ‘READY TO BREW’ indication will return to the LCD Control Center in about 15-30 sec. NOTE: Following the brew, your Brewer will fill in preparation for the next brew. The pump will make a vibrating sound. This is normal. Stopping the Brew Process If you need to stop the brewing after the process has started, press and release the Power Switch to turn the Brewer ‘OFF’. The flow of coffee or tea will stop, the heating element will shut off and the blue lights illuminating the LCD Control Center and Water Reservoir will disappear. NOTE: You may get less coffee or tea in your cup during your next brew. We recommend that you perform a cleansing brew with water only after a terminated brew. Then your NEXT brew will be the volume you have selected. Adding Water The LCD Control Center of your Brewer will indicate when the water level in the tank is low or if the Water Reservoir has been removed by displaying the words ‘ADD WATER’. The Brewer will not allow you to initiate a brew when ‘ADD WATER’ is displayed. The Water Reservoir can be filled in two ways. 1. Lift off the Water Reservoir Lid and pour water directly into the Water Reservoir while it is still attached to the Brewer, then replace the Lid. 2. Remove the Water Reservoir from Brewer by first removing Lid from the Water Reservoir, then lifting the Water Reservoir straight up and toward front of Brewer. Fill with water. Place the Water Reservoir back on the Brewer and replace the Lid. IMPORTANT: Do not remove the Water Reservoir during the brewing process. Brewing Hot Water Your Brewer is able to produce a cup of hot water for making Ghirardelli Premium Hot Cocoa, for use in cooking, for making soups, etc. Simply follow the instructions on page 7 “ Ready To Brew Your First Cup” without adding a K-Cup® Portion Pack. Purging the Brewer If your Brewer has not been used for more than one week, you should purge the water from the inner tank. 1. If there is water in the Water Reservoir, remove the Lid, then lift the Water Reservoir straight up and toward front of the Brewer. Discard water, rinse and refill with bottled or filtered water. Place the Water Reservoir back on the Brewer and replace the Lid. (If there is no water in the Water Reservoir, simply refill.) 2. Be sure the Brewer is turned on...