Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
IMPORTANT: You cannot use your Keurig brewer until it has been primed for its first use as set forth below. Please follow these easy steps and you will discover what Deliciously Simple™ truly means. Please note, if your Brewer has been exposed to temperatures below freezing, it is recommended you allow two hours for an unpacked brewer to warm to room temperature before priming or brewing. 1. Unpacking the Elite - ModelB40 Brewer a. Carefully remove the Brewer by placing the box on its side, and pulling the Brewer out of the box and removing the protective materials. b. Place the Brewer upright on a flat surface. Remove three pieces of adhesive tape from Brewer. c. Unwrap cord and plug Brewer into a grounded outlet. 2. Priming a. Press Power Button to turn the Brewer on and the green light next to the Power Button will become illuminated. b. The blue light next to ‘ADD WATER’ will be illuminated. Remove the Water Reservoir from Brewer by first removing Lid from Reservoir, then lifting Reservoir straight up and away from Brewer. Rinse and fill with cold water. Replace the Water Reservoir back on the Brewer and replace the Lid. c. Place a cup or mug on the Drip Tray Plate. d. The red light next to ‘DE-SCALE’ on the LED Control Center will flash to indicate that the Brewer is in its initial PRIME sequence. This light will continue to flash until the PRIME sequence is complete. e. The green light above the Brew Button will flash. If it is not flashing, ensure that the handle is pressed all the way down. Press the Brew Button to start the initial PRIME. f. The Brewer will automatically fill (priming it) and then the water will be heated. This will take about 3 minutes. During the heating period, the red light next to 'HEATING' will become illuminated. When the water is heated, the red light will turn off and the green light above the Brew Button will flash. g. Press the Brew Button to start a cleansing brew, during which hot water will flow into your cup or mug. Pour the hot water into the sink. h. The Brewer may take 15 seconds to reheat between brews and the red light next to ‘HEATING’ will be illuminated. During this time the pump may cause a vibration noise. This is normal. The red light will turn off when the water has heated and the Brewer is ready. i. The one-time priming process is now complete and you are ready to brew! 3. Choose a. Place a cup or mug on the Drip Tray Plate. b. Select a K-Cup® portion pack. Do not remove the foil lid. 4. Brew a. Lift the Handle, place the K-Cup in the K-Cup Holder Assembly and then push the Handle all the way down to puncture the K-Cup. Please be careful to avoid the sharp needles in the K-Cup Assembly Housing & Lid. b. Press the Brew Button located below the flashing green light. This will yield a 7.25 oz serving. If the green light is not flashing, be sure the handle is all the way down. Please consult the Use & Care Guide for additional information on your Brewer. If you are experiencing problems, contact Customer Service at 1-866-901-BREW (2739). Part #: 60-200258-034 © 2005 Keurig Incorporated Revision A, April 2005 b06739_QuickStartInsert_B40 4/28/05 4:00 PM Page 2 KEURIG® Guide de demarrage Premium Coffee Systems Premium Coffee Systems Laissez-vous charmer SANS TARDER! Merci d’avoir achete une cafetiere Keurig® Elite - Modele B40, le systeme d’infusion une tasse a la fois pour la maison. IMPORTANT : N’utilisez pas votre cafetiere Keurig avant de l’avoir preparee pour une premiere utilisation, tel qu’indique ci-dessous. Veuillez suivre les cinq etapes faciles suivantes,...