Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
COFFEE READY. The machine will automatically remind you when it’s time to decalcify again. 17.2 MANUAL DECALCIFYING If you use very hard water it is possible that calcium builds up prematurely. If your coffee does not come out as hot as before it is a sign for calcium build-up. When this happens you can manually start a decalcifying cycle as follows: COFFEE READY • Push the Rotary Dial until the display shows MAINTENANCE. • Push the Rotary Dial, display shows CLEAN CAPPUCCINO. • Turn the dial until the display shows DECALCIFY MACHINE and push the dial. The display shows DURATION 45 MIN. / START YES. • Continue with the steps 2 through 15 from the chapter 17.1. 34. 18. TIPS FOR BETTER COFFEE Height adjustable coffee-spout Adjust the height of the coffee-spout to the size of your cups. Grinding Please refer to chapter 7 "Adjusting the Grinder." Pre-warm cups Pre-warm cups in advance with hot water (chapter 9a). Sugar and cream Warmth is lost by stirring the contents of the cup. Adding milk or cream from the refrigerator considerably lowers the temperature of the coffee. 19. ERROR MESSAGES / TROUBLESHOOTING ERROR MESSAGES: The machine can display any of the following error messages: ERROR 1, ERROR 3, ERROR 5 Call our customer service hot line 1-800-220-5701. Your machine needs to be returned for service. ERROR 2, ERROR 4 Your machine is too cold. The heating sensor does not react. • Turn the machine off. • Keep the machine at normal room temperature (65. F or higher) for 2 hours . • Then turn it on again. If display still shows ERROR 2 or ERROR 4 call customer service. ERROR 6, ERROR 7, ERROR 8 • Turn machine off, turn the main power switch off and unplug machine for a minute. • Turn machine on again. If the error message comes up again, try one more time. • If the message persists, call customer service. TROUBLESHOOTING: A. NO COFFEE COMES OUT OF THE COFFEE SPOUT Reason: Beans in bean container are not feeding properly into the grinder because they are stuck together. Solution: Stir beans before grinding and while grinding turn the grinding selector to the coarsest setting. When using very oily beans pour the beans onto a plate and let some of the sticky oils evaporate (this will not harm the aroma of the coffee). Reason: You used ground coffee in the ground coffee funnel. The ground coffee was too fine. Solution: Use ground coffee which is ground somewhat coarser. Reason: No water is transported through the system. Solution: Remove water container and make sure that the connecting valve is free of any particles (like a coffee bean etc). Reason: The ground coffee funnel is clogged; the internal brewing chamber is clogged. Solution: Place a large cup underneath the coffee spout. Push the rinse button (Fig. 2E) a few times until the blocked coffee is removed. (Never fill more than 2 scoops of coffee in the ground coffee funnel; the funnel is not a storage area for ground coffee). Also, use a ground coffee which is ground somewhat coarser. 35. B. THE DISPLAY READS "FILL WATER TANK" BUT THERE IS ENOUGH WATER IN THE WATER TANK. Reason: The floatation device (Fig.1,4) is stuck or missing. Solution: Clean the water container and make sure the floatation device moves freely. Solution: Within the water tank is a small compartment (like a mouse trap). Inside is a small black floatation device. On top is a small clear see-through plastic cover. This small plastic cover is missing and the floatation device is outside of the small compartment. Check if you can find both pieces inside the water tank and put it back together. If you cannot find the pieces call 1-800-220-5701. We will send the pieces FREE OF CHARGE. C. INSUFFICIENT FROTHED MILK PRODUCTION Reason: Milk is initially not cold enough or your milk is not suited for thick frothing. Solution: Make sure milk is cold. Use a different type of milk. Skim milk will produce the thickest and longest lasting froth. Full fat milk will produce less thick froth. Reason: The components of the frothXpress are not assembled properly, or the components are clogged with hardened milk, or one or more of the components are missing. Solution: a. Remove frothXpress. Check that steam comes out of the steam nozzle. Place a cup underneath the steam nozzle and use the milk function (chapter 10e). CAUTION: hot steam is dispensed from the steam nozzle. If no steam is released stop the milk function and use a needle to clear blockage inside the steam nozzle. b. Clean all frothXpress parts and assemble properly (chapter 15.5). c. If any parts are missing call: 1-800-220-5701. D. GRINDER MAKES AN EXTREMELY LOUD NOISE; NO BEANS ARE GROUND Reason: A stone or object is blocking the burr grinder. Solution: See chapter 15.2. E. THE REMOVABLE DRAWER (Fig.1, 18) DOESN’T COME OUT Reason: The internal used coffee disposal chute did not retract. Solution: Turn off the machine. Wait a minute. Turn machine on and wait until it stops making any noise. Now try to pull out the drawer. If this does not work, ...