Votos - 6, Puntuación media: 4
(
)
)
|
Resumen del manual
The water will reach the correct temperature in approximately 2 minutes. The BREW Button will turn solid red and your beverage will start to dispense. If you are performing an initial cleansing brew, discard the water from the mug and begin at Step 4 to brew your first beverage. if you have previously completed an initial cleansing brew, enjoy your beverage. Your Brewer is now ready for the next beverage. Begin the process again, adding fresh water and a new K-Cup. 11 SeCtIon 5 Cleaning & Maintenance cleaning External Parts IMPORTANT: Make sure the Brewer is unplugged before cleaning. Regular cleaning of the Brewer’s external components is recommended. 1. Never immerse the Brewer in water or other liquids. The Brewer housing and other external components should be cleaned with a damp, non-abrasive, lint-free cloth. 2. The Drip Tray and Drip Tray Plate should be periodically inspected and cleaned with a damp, non-abrasive, lint-free cloth. The Drip Tray and Drip Tray Plate should not be put into the dishwasher. To remove the Drip Tray, simply slide it toward you. Remember, when the red Drip Tray Overfill Indicator appears, the Drip Tray is almost full. Carefully remove the Drip Tray and discard its contents. The Drip Tray has a snug fit to ensure it stays put in transit. cleaning the K-cup® Portion Pack Holder assembly 1. Cleaning the Parts — The K-Cup Holder Assembly can be placed onto the top shelf of a dishwasher. NOTE: Use low temperature cycles in the dishwasher. To remove the K-Cup Holder Assembly from the Brewer, lift the Brewer Handle to open. Grasp the top of the K-Cup Holder with one hand. With the other hand, push up on the bottom of the K-Cup Holder until it releases (fig. 1). After cleaning, align the K-Cup Holder with the opening using the two front ribs as a guide, and snap into place from the top (fig. 2). fig. 1 fig. 2 12 13 2. Cleaning the Funnel — The Funnel can be removed from the K-Cup Holder by pulling on it until it snaps off (fig. 3). The Funnel can be placed on the top shelf of a dishwasher. NOTE: Use low temperature cycles in the dishwasher. To replace the Funnel, just snap it back onto the K-Cup Holder Assembly. 3. Cleaning the Exit Needle — The Exit Needle is located on the inside bottom of the K-Cup Holder Assembly. Should a clog arise due to coffee grinds, it can be cleaned using a paper clip or similar tool. Remove K-Cup Holder Assembly and detach Funnel. Insert the paper clip (fig. 4) into the Exit Needle to loosen the clog and push it out. The K-Cup Holder can be placed on the top shelf of a dishwasher. NOTE: Use low temperature cycles in the dishwasher. The Entrance Needle does not require cleaning. ! fig. 3 fig. 4 CAUTION: There are sharp needles that puncture the K-Cup above the K-Cup Holder and in the bottom of the K-Cup Holder. To avoid risk of injury, do not put your fingers in the K-Cup Assembly Housing. NOTE: Over time, discoloration, spotting or staining may appear in the Cold Water Reservoir. This is normal and will vary depending on the mineral content of the bottled or filtered water used. This will not affect the operation of the Brewer. However, be sure to clean the Cold Water Reservoir regularly to minimize build-up (see page 14). 2. Cleaning the Funnel — The Funnel can be removed from the K-Cup Holder by pulling on it until it snaps off (fig. 3). The Funnel can be placed on the top shelf of a dishwasher. NOTE: Use low temperature cycles in the dishwasher. To replace the Funnel, just snap it back onto the K-Cup Holder Assembly. 3. Cleaning the Exit Needle — The Exit Needle is located on the inside bottom of the K-Cup Holder Assembly. Should a clog arise due to coffee grinds, it can be cleaned using a paper clip or similar tool. Remove K-Cup Holder Assembly and detach Funnel. Insert the paper clip (fig. 4) into the Exit Needle to loosen the clog and push it out. The K-Cup Holder can be placed on the top shelf of a dishwasher. NOTE: Use low temperature cycles in the dishwasher. The Entrance Needle does not require cleaning. ! fig. 3 fig. 4 CAUTION: There are sharp needles that puncture the K-Cup above the K-Cup Holder and in the bottom of the K-Cup Holder. To avoid risk of injury, do not put your fingers in the K-Cup Assembly Housing. NOTE: Over time, discoloration, spotting or staining may appear in the Cold Water Reservoir. This is normal and will vary depending on the mineral content of the bottled or filtered water used. This will not affect the operation of the Brewer. However, be sure to clean the Cold Water Reservoir regularly to minimize build-up (see page 14). SeCtIon 5 Cleaning & Maintenance (continued) cleaning the cold Water Reservoir To access the Cold Water Reservoir, lift the Cold Water Reservoir Lid. Remove the Water Level Guide (fig. 5), then clean the inside of the reservoir with a damp, lint-free cloth as necessary (fig. 6). Replace the Water Level Guide and close the Cold Water Reservoir Lid when finished. NOTE: The Water Level Guide is not di...
Otros modelos de este manual:Cafeteras - B31 (883.34 kb)