Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
Shake off any access water and wait for one minute. • If all five fields of the test stick turn reddish, set the hardness level to 4. If four fields turn reddish, set the hardness level to 3. If three or less fields turn reddish, leave the level in position 2. You can change the hardness settings as follows: COFFEE READY • Open cover for programming buttons (Fig.1,19) and press and hold the P button (Fig.3A,P) until you hear a beep. PRESS KEY / POWDER QUANTITY • Press the + button several times until the display shows: HARDNESS LEVEL 2. • Press the P button. You will hear one beep. 13. • You can now change the hardness level by pressing the + button until the desired level is displayed. • Press the P button once again to confirm. Another beep will be heard. • Press the N button. The display will show COFFEE READY. In level – – the water hardness monitor is turned off. IMPORTANT: Turning the monitor off requires you to use the Claris filter cartridge or distilled water. 11. CLARIS WATER CARTRIDGE The machine comes with one free Claris water cartridge. The Claris water cartridge is specially made for use with the Impressa machines. The Claris cartridge: • Reduces the water hardness up to 75%. • Removes (if present) up to 85% chlorine, up to 90% lead, up to 95% copper and up to 67% aluminum. • Cleans the water through an upward current principle (See Fig. 10) just before the brewing cycle starts, ensuring freshly filtered water every time you make coffee. • Eliminates decalcifying. When using the Claris water cartridge, you never need to decalcify your machine. • Is available through your retailer, the enclosed mail order form, or through or call 1-800-220-5701. 11a. INSTALLING THE CLARIS CARTRIDGE • Make sure the water tank is empty. • Remove cartridge from its bag. • Snap the Claris extension tube on top of the cartridge (Fig. 11). • Open water container lid and pull up the holder for the Claris cartridge (Fig.12). • Insert the cartridge with its tapered end down and the extension piece up. Make sure it fits snugly over the white mesh piece inside the water container. Push down gently (Fig.13). • Close the holder for the cartridge so that it engages in the water tank (Fig.12). • Fill the water tank with fresh cold water and replace. 11b. PROGRAMMING THE CLARIS CARTRIDGE COFFEE READY. • Open cover for programming (Fig.1,19). • Press the P button until you hear a beep. PRESS KEY / POWDER QUANTITY. • Press the + button several times until the display shows: FILTER NO • Press the P button (you will hear a beep). The word NO flashes. • Press the + button once and the word YES flashes. • Press the P button to confirm. RINSE FILTER / PRESS STEAM. • Place a large container (approx. 1 liter or at least 22 oz.) under the steam nozzle (Fig. 4) and press the PERMANENT STEAM button (Fig.3,M). PLEASE WAIT / FILTER RINSING. Water will be pushed through the steam nozzle and will stop automatically. The water might be slightly discolored. Discard water. This procedure activates the Claris cartridge. FILTER YES • Press the N button. COFFEE READY IMPORTANT: If you select "YES" for the Claris Cartridge the function WATER HARDNESS is suppressed and turned off. 11c. REPLACING THE CLARIS CARTRIDGE The filter is monitored automatically. After approx. 50 liters (approx. 55 quarts) of water, the filter loses its effect. The display will show: REPLACE FILTER Attention: The filter should be changed every 2 months if you use less than 50 liters. In this case, no message will appear in the display. • Remove the old cartridge, snap the extension tube onto the new cartridge and install. The old cartridge is environmentally friendly. Dispose with regular household trash. • Fill water tank with fresh water. • Open front cover and press the CLARIS button (Fig.3A,R). for a few seconds until you hear a beep. RINSE FILTER / PRESS STEAM • Place a large container (approx. 1 liter or at least 22 oz.) under the steam nozzle and then press the PERMANENT steam button (Fig.3,M). PLEASE WAIT / FILTER RINSING Water will be dispersed into the container and will stop automatically. When the cycle stops the machine will display COFFEE READY. 12. MAKING ESPRESSO AND “CREMA COFFEE” To understand the principles of pressure brewing refer to chapters 4. through 4.3. 14. Push the ON/OFF button to turn the machine on. PLEASE WAIT The machine is heating up. Then the display will read: RINSE UNIT • Place an empty cup under the coffee-spout (Fig. 8b) and press the RINSE button (Fig. 2,F). UNIT RINSING COFFEE READY You are now ready to make coffee. • Place 1 or 2 cups under the coffee-spout and press one of the cup buttons (Fig. 2; C,D,E,G,H). The pre-brew system moistens the coffee powder, briefly interrupts the flow and then starts the real brewing process. IMPORTANT: You can stop the flow of coffee at any time by pressing any of the coffee buttons. • Adjust the coffee-spout (Fig. 8a,8b) to the size of your cups. 12a. USING GROUND COFFEE • Open cov...
Otros modelos de este manual:Cafeteras - Impressa S8 (479.73 kb)
Cafeteras - Impressa S9 (479.73 kb)