Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
2 The machine shows this display. Wait for the cycle to fi nish automatically. Note: You can stop dispensing by pressing the “ ” button. Green Yellow 3 When the above steps are complete, the machine shows this display. You can now perform the manual rinse cycle. Yellow 10 ENGLISH Manual Rinse Cycle During this process you activate the coff ee brewing cycle and fresh water fl ows through the steam/hot water circuit. This takes a few minutes. 1 Place a container under the dispensing spout. Green 2 Check that the machine shows this display. 3 To select the pre-ground coff ee brewing function press the " " button, until the following display is shown. Note: Do not add pre-ground coff ee to the compartment. 4 Check that the selection lever is set to “ESPRESSO”. Press the “ ” button. The machine starts dispensing water. 5 When the dispensing has fi nished, empty the container. Repeat the operations from step 1 to step 4 twice, then continue with step 6. Green 6 Place a container under the Classic Milk Frother. ESPRESSO ENGLISH 11 1111 Green Red Red 7 Press the “ ” button. The machine shows this display. 8 Press the “ ” button to start dispensing hot water. 9 Dispense water until the no water icon appears. Note: You can interrupt the manual rinsing by pressing the “ ” button. To restart press the “ ”button and then the “ ” button. 10 Fill the water tank again up to the MAX level. Now the machine is ready for coffee brewing. The display to the left will be shown. Note: When the machine has not been operated for at least two weeks, it will automatically perform a start-up rinse/self-cleaning cycle. Following this, you need to initiate a manual rinse cycle as described above. The automatic rinse/self-cleaning cycle starts automatically when the machine has been in stand-by mode or switched off for more than 15 minutes. At the end of the cycle, it is possible to brew a coffee. 12 ENGLISH Measuring and Programming Water Hardness Water hardness measuring is very important in order to define the descaling frequency and to install the “INTENZA+” water filter (for more detail on the water filter, see next chapter). To measure the water hardness follow the steps below: 1 Immerse the water hardness test strip (supplied with the machine) in water for 1 second. Note: The test strip can only be used for one single measurement. 2 Wait for one minute. 2 3 4 A B C Intenza Aroma SystemMachine Water Hardness Setting 1 3 Check how many squares have changed to the color red and then refer to the table. Note: The numbers on the water hardness test strip correspond to the water hardness adjustment settings. More precisely: 1 = 1 (very soft water) 2 = 2 (soft water) 3 = 3 (hard water) 4 = 4 (very hard water) The letters correspond to the references that are located at the base of the “INTENZA+” water filter (see next chapter). Yellow 4 Press the “ ” button and scroll the pages by pressing the “ ” button until the following icon is displayed. Note: The machine is supplied with a standard water hardness setting, suitable for most types of water. ENGLISH 13 1313 5 Press the “ ” button to increase the value or the “ ” button to decrease the value. 6 Press the “ ” button to confirm the setting. 7 Press the “ ” button to exit the programming MENU. The machine shows this display and is ready to brew. “INTENZA+” Water Filter Installation We recommend that you install the “INTENZA+” water filter as this prevents limescale build-up in your machine and preserves a more intense aroma of your coffee. The “INTENZA+” water filter can be purchased separately. For further details, please refer to the maintenance products page in this manual. Water is a crucial part of every espresso/coffee, so it’s important to always have it professionally filtered. Using the “INTENZA+” water filter will prevent mineral deposits from building up and improve your water quality. 1 Remove the small white filter from the water tank and store it in a dry place. 2 Remove the “INTENZA+” water filter from its packaging, immerse it vertically (with the opening positioned upwards) in cold water and gently press the sides so as to let the air bubbles out. Green Yellow 14 ENGLISH 3 Set the “INTENZA+” water filter according to the measurements performed (see previous chapter) and indicated on the base of the fi lter: A = soft water – equals 1 or 2 on the test strip B = hard water (standard) – equals 3 on the test strip C = very hard water – equals 4 on the test strip 4 Put the “INTENZA+” water filter into the empty water tank. Press it down until it cannot move any further. 5 Fill the water tank with fresh water and reinsert it into the machine. 6 Dispense all the water of the tank by using the hot water function (see “Hot Water Dispensing” chapter). 7 Fill the water tank again. 8 Press the “ ” button and scroll the pages by pressing the “ ” button until the following display is shown. 9 Press the “ ” button to select “ON” and press the “ ” button to confi rm. ” button. The machine ...