Votos - 3, Puntuación media: 3.3
(
)
)
|
Resumen del manual
. . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation and Start-up . . . . . . . . . . . . . . . . . . .4 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Programming . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Precision Brew® Control Board . . . . . . . . . . . .15 Troubleshooting Error Messages . . . . . . . . . . . . . . . . . . . . .17 Filling Problems . . . . . . . . . . . . . . . . . . . . .17 Heating Problems . . . . . . . . . . . . . . . . . . . .19 Brewing Problems . . . . . . . . . . . . . . . . . . . . 21 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Parts Photos . . . . . . . . . . . . . . . . . . . . . . . . . . .25 VS-1.5(S) Cleaning and Sanitizing . . . . . . . . . .29 Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . .30 Prior authorization must be obtained from Grindmaster Corporation for all warranty claims. © Grindmaster Corporation, 2004 PRINTED IN U.S.A. Models PB-330/PB-330E 230V Models PBIC-430/ PBIC-430E230V Models PBVSA-430/ PBVSA-430E 230V Grindmaster Corporation 4003 Collins Lane Louisville, KY 40245 USA (502) 425-4776 (800) 695-4500 (USA & Canada only) (800) 568-5715 (Technical Service Only) FAX (502) 425-4664 0607 Form # AM-344-04 Part # A090-840 Warning Labels The following warning labels were on your dispenser when it was shipped from the factory. They should remain on your dispenser in good, readable condition at all times. If one of your labels is missing or damaged, order a replacement label immediately. Part # A546-445 Located on front splash panel and lid of machine. Located on PB-330, PB-330E 230V, PB-430, and PB-430E 230V lower front decal. Order part # A546-434 for PB-330. Order part # A546-435 for PB-430. Located on PBIC-330, PBIC-330E 230V, PBIC-430, and PBIC-430E 230V above faucet. Order part # A546-428 for PBIC-330. Order part # A546-427 for PBIC-430. Part # A546-213 Located on front splash panel. Part # A71949 Located on brew baskets. CAUTIONRemovewithcare. Hotliquidinbrewbasketcouldcauseburns. Shuttle Brewers & Airpot/Shuttle Brewers Page 3 Installation WARNING ELECTRIC SHOCK HAZARD! Installation of this appliance should be performed by qualified service personnel only. Improper installation could result in electrocution. Set-Up/Position 1) Remove the brewer from the packing material and attach its legs. 2) Position the brewer on a strong, stable table or counter. Check the level front to back and side to side. Adjust the legs to the correct level. IMPORTANT: THE PERSON INSTALLING THIS APPLIANCE IS RESPONSIBLE FOR ENSURING THAT ELECTRIC AND WATER CONNECTIONS MEET THE REQUIREMENTS OF THE NATIONAL ELECTRIC CODE, NATIONAL PLUMBING CODE, AND ANY LOCAL ORDINANCES. The electric and water hook-up locations are behind the front panel. Remove the four screws fastening this panel for access to these connections. Water Hook-up 1) The water line may enter through holes on the rear or the bottom of the brewer. Use the right hand opening for water. 2) Use 3/8” copper or flexible water line to prevent strain. Do not use low temperature plastic tubing. The connection to the fill valve is 3/8” flare. 3) Water line pressure must be from 30 to 80 psi (207-2 KPA). 4) Hot (up to 160°F/71°C) or cold water may be used. Hot water offers faster recovery between brews. 5) Install a shut-off valve near the brewer. 6) Installing a filtering system can improve the taste of brewed coffee and extend the life of the brewer. If your water has high calcium (lime), chlorine, or iron content, this is especially important. The filter should be the lime inhibiting type if cold water is used. Page 4 Shuttle Brewers & Airpot/Shuttle Brewers Installation (cont.) Electric Hook-up The brewer is designed to operate at the specified voltage on the nameplate with a tolerance of ± 10% for voltage deviation. It is very important that the power line to the brewer be checked to make sure that the voltage is within 10% of the brewer’s rated voltage. Failure to provide adequate voltage, as defined above, will cause problems with your brewer. If the power is too low, the solenoid valves may or may not work or longer recovery time will be experienced. The brewer may be permanently damaged if the voltage is too high. 1) The electric ratings for your brewer are printed on its nameplate. 2) The brewer should be connected to its own circuit with a fused disconnect switch or a circuit breaker near the brewer. Important: For CE units, means shall be provided to endure all pole disconnection from the supply. Such means shall be one of the following: a supply cord fitted with plug, or a switch that is directly connected to the supply terminals and has a contact separation of at least 3mm in each pole. 3) Attach the app...