Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Pressing and holding the push button will cause hours to increase more rapidly. Pulse the push button to increase hour more slowly. When the number count passes 12, the PM light activates and will be displayed on the LCD. After setting the time, the default hour is the last time set unless power is lost. b. “Minute” Button: To change the minute, press the “Minute” push button. Pressing and holding the push button will cause minutes to increase more rapidly. Pulse the push button to increase minutes more slowly. After setting the time, the default minute is the last time set, unless power is lost. Note: As you scroll, the numbers will advance slowly at first and then speed up to the rate of about three per second. When the number displayed approaches the desired setting, release the button and press repeatedly to advance one digit at a time. 3. To program the Auto On: Turn the function knob to “Program” to set the desired time to engage the Auto On. Change the auto on time in the program setting using the minute and hour push buttons, as you would to set the time of day. Then turn the function knob to “Auto On”. The LCD will display the current time. Lift and release the flip switch. The green light comes on to signal that the programming function is in use, and the brewing cycle will begin at the programmed time. At the programmed time, the red light will come on with the green light, indicating that the brewing cycle is starting. Both lights will go off after keep warm cycle. To turn off: Depress the flip switch down and release. Note: To activate the auto-on feature again for brewing the next day, you must lift and release the flip switch; the green auto-on light will turn on. 4. To program the Variable Auto Off: Turn the function knob to the “Auto Off” position. Press and hold the “Hour” button for two seconds, until the clock display starts blinking. To change the hour and minutes, use the push buttons as you would to set the time of day. The Auto Off time can be set from zero to four hours. 5. Decalcification: Decalcification refers to the removal of calcium deposits which form over time on the metal parts of the coffeemaker. For best performance from your Brew Central™ Coffeemaker, decalcify the base unit from time to time. The frequency depends upon the hardness of your tap water and how often you use the coffeemaker. The flashing Self Clean light will indicate when you should clean your coffeemaker. Self Cleaning If the Self Clean light begins to flash when the coffeemaker is turned on, it is telling you that the calcium buildup is interfering with the functioning of your coffeemaker and the flavor of your coffee. To clean, fill the water reservoir to capacity with a mixture of 1/3 white vinegar and 2/3 water. Press the Self Clean button. When the self clean light glows, turn the coffeemaker on by pressing the flip switch to ON. The Self Clean light will shine steadily. The coffeemaker is now in Self Clean mode. One cycle should be sufficient to adequately clean the coffeemaker. When the cycle is completed and the five beeps sound, the coffeemaker will shut off. Turn the coffeemaker ON to see if the Self Clean light continues to flash. If it does, turn it to OFF and then repeat the cleaning procedure with a fresh solution of vinegar and water. If the Self Clean light no longer flashes, turn the coffeemaker to OFF and then run one cycle of fresh cold water through the unit before using the unit again to brew coffee. Notes on the Self Clean Function Pressing the Self Clean button cancels all other settings. If it is pressed accidentally, press it again to return the coffeemaker to all its previous settings. Pressing ON/OFF will also exit the Self Clean Mode and turn the coffeemaker OFF. 6. 1-4 Cup Setting: The 1-4 cup setting button is used when you make small amounts of coffee. Normal coffeemakers will produce a colder batch of coffee when smaller amounts are made, because the heater doesn't have enough time to properly ‘warm up’ to heat a small amount. The 1-4 setting basically ‘double heats’ the water, making your smaller amount as piping hot as a full pot would be. To use: When making a smaller amount, press the 1-4 button on the control panel after turning on the unit. 7. Heater Plate ‘Keep Warm’ Control: The knob on the right of the control panel is the heater plate control setting for after brewing temperature. You can choose one of three heat settings to keep your coffee warm: low, medium, or high. MAKING COFFEE Before you make the first pot of coffee in your new Cuisinart® Brew Central™ Coffeemaker, we recommend operating the coffeemaker once using only water and a paper filter. This will remove any dust or residues that remain in the system from the manufacturing process. 1. Insert the Water Filter: a. Remove the filter from polybag and soak in cold tap water for 15 minutes. b. Remove the water filter holder from the coffeemaker by lifting it out of the reservoir area with your thumb and for...