Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
¦ Increase the separation between equipment and receiver. ¦ Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. ¦ Consult the dealer or an experienced radio/television technician for help. ¦ Use a shielded and properly grounded I/O cable and power cable to ensure compliance of this unit to the specified limits of the rules. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Adaptec, Inc. ACS-100 Tested to Comply With FCC Standards FOR HOME OR OFFICE USE European Union Compliance Statement This Information Technology Equipment has been tested and found to comply with EMC Directive 89/336/EEC, as amended by 92/31/EEC and 93/68/EEC, in accordance with: ¦ EN55022 (1998) Emissions ¦ EN55024 (1998) Immunity: – EN61000-4-2 (1998) Electrostatic discharge: ±4 kV contact, ±8 kV air – EN61000-4-3 (1998) Radiated immunity – EN61000-4-4 (1995) Electrical fast transients/burst: ±1 kV AC, ±0.5 kV I/O – EN61000-4-5 (1995) Surges ±1 kV differential mode, ±2 kV common mode – EN61000-4-6 (1996) Conducted immunity: 3 V – EN61000-4-11 (1994) Supply dips and variation: 30% and 100% In addition, all equipment requiring U.L. listing has been found to comply with EMC Directive 73/23/EEC as amended by 93/68/EEC in accordance with EN60950 with amendments A1, A2, A3, A4, A11. Canadian Compliance Statement This Class B digital apparatus meets all requirements of the Canadian Interference- Causing Equipment Regulations. Cet appareil numerique de la classe B respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada. 3 In this Guide... Kit Contents 5 System Requirements 5 Getting Started Checklist 6 Installing the Device Driver–Windows 98SE Only 6 Installing a Disk Drive 7 Connecting and Powering On 9 Next Steps 9 Disconnecting Your USB Enclosure 10 Troubleshooting 11 This User’s Guide explains how to install and connect your Adaptec® ACS-100 USB Enclosure. 4 Kit Contents ¦ Adaptec ACS-100 USB Enclosure ¦ One enclosure stand ¦ One power adapter ¦ One high-quality USB cable ¦ One bag of screws ¦ CD, including device drivers and documentation A disk drive is not included in the kit. The Adaptec ACS-100 USB Enclosure supports 3.5-inch IDE hard disk drives. System Requirements To successfully install and use your Adaptec ACS-100 USB Enclosure, your computer must meet these requirements: ¦ Microsoft® Windows® computers must be running Windows XP, Windows 2000, Windows Me, or Windows 98SE Macintosh computers must be running OS 9.2.2 or later for USB 1.1 support, or OS 10.2.7 or later for USB 2.0 support ¦ Available USB port (see About USB 2.0 Performance below for more information) ¦ CD-ROM drive About USB 2.0 Performance Your Adaptec ACS-100 USB Enclosure is a USB 2.0 device. For it to operate at USB 2.0 speeds, it must be connected to a USB 2.0 port, and USB 2.0 drivers must be installed on your computer. If your computer does not have a built-in USB 2.0 port, Adaptec recommends connecting the USB Enclosure to an Adaptec USB 2.0 adapter for the highest-quality USB 2.0 connection. 5 Getting Started Checklist Complete these steps to install and begin using your Adaptec ACS-100 USB Enclosure: . Install the device driver—Windows 98SE only (see below). . Install a disk drive (see page 7). . Connect the enclosure and power it on (see page 9). . Prepare the disk drive for use (see page 9). Installing the Device Driver–Windows 98SE Only Note: Windows XP/2000/Me and Macintosh users—No driver installation is required. Your Adaptec ACS-100 USB Enclosure works with the drivers built into your operating system. Continue with Installing a Disk Drive on page 7. Before you begin, ensure you have the most recent operating system updates installed on your computer. Refer to the Microsoft Web site to download updates. To install the device driver: 1 Power on your computer, if you have not already done so. 2 Insert the CD into your CD-ROM drive. 3 From the Windows Start menu, click Run, then click Browse. 4 Browse to the CD-ROM drive, then double-click Setup.exe to begin the driver installation. 5 Follow the on-screen instructions to install the driver. 6 7 Installing a Disk Drive Before you begin, ensure that you are installing the proper disk drive. The Adaptec ACS-100 USB Enclosure supports 3.5-inch IDE hard disk drives only. Note: You need a Phillips screwdriver to complete this task. To install a disk drive into your USB Enclosure: 1 Use a screwdriver to remove the two screws on the back of the enclosure. 2 Remove the enclosure’s back panel, as shown below, and slide out the disk drive tray. 3 Connect the disk drive tray’s internal power connector and IDE cable to the disk drive. 8 4 Place the disk drive into the disk drive tray and secure it, using the four screws...