Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
Disconnect the Aux-In cable. 50 Chapter 3 2. Disconnect the CD-In cable. 3. Disconnect the floppy cable. 4. Disconnect the IDE1 and IDE2 cable. Removing the Modem card, CD-ROM, Floppy and HDD NOTE: There have the hook lock on CD-ROM, floppy and HDD cage, in other words, please move a little bit forward to release the lock then you can disassemble these parts smoothly. 1. Detach the modem card. 2. Disconnect the CD-ROM power, IDE and CD-In cables. 3. Disconnect the floppy cable and power cable. 4. Disconnect the HDD power cable and IDE cable. Chapter 3 51 5. Press the latch and remove the CD-ROM drive. 6. Press the latch and remove the floppy drive. 7. Press the latch again to release the hard disk module. 8. Detach the HDD from the bracket. Removing the Power Supply 1. Remove the main ATX power connector as shown here. 2. Remove the Pentium 4(ATX-12V) power connector as shown here. 3. Remove the four screws as shown here. 52 Chapter 3 4. Remove the power supply. Removing the Heatsink and the CPU ( for T130) 1. First of all, disconnect the CPU fan power cable. 2. Remove the 4 screws first. 3. Take the CPU fan after you remove screws. 4. Press the latch outward with a flat screw driver to release it. 5. Then hold the both sides to take the latch and heatsink away. 6. Take the retention module away. 7. Pull the CPU bar up to 90 degrees. 8. Then take the CPU away from mainboard. Chapter 3 53 Removing the Memory 1. Pop out the memory and remove it as shown here. Removing the Mainboard 1. Remove the six screw as shown here. 2. Remove the motherboard as shown here. Removing the Power Button 1. Remove the power button as shown here. Removing the LED Module 1. Remove the LED module by following the instructions here. 54 Chapter 3 Removing the Daughter Board 1. Remove the screw as shown here. 2. Detach the USB cable and audio cable from the daughter board. Chapter 3 55 Standard Reassembly Procedure This section tells you how to reassemble the system when you need to perform system service. Please also refer to the assembly video, if available. Installing the Daughter Board 1. Connect the audio cable and USB cables to the daughter board. 2. Fasten the daughter board with one screw as shown here. Installing the LED Module 1. Install the LED module by following the instructions here. Installing the Power Button 1. Attach the power button as shown here. Installing the Mainboard 1. Put the motherboard to the original position as shown here. 56 Chapter 3 2. Secure the motherboard with the six screw as shown here. Installing the Heatsink and the CPU (please refer to disassemble photos) 1. Place the CPU to the CPU socket. 2. Place the rentention module next to previous installing. 3. Place the heatsink then hook the latch to the tabs. 4. Then place the CPU fan on the heatsink. Installing the Memory 1. Insert the memory to the DIMM slot as shown here. Installing the Power Supply 1. Place the power supply to the original position as shown here. 2. Secure the power supply with the four screws as shown here. 3. Connect the Pentium 4(ATX-12V) power connector to the motherboard as shown here. Chapter 3 57 4. Connect the main ATX power connector to the motherboard as shown here. Installing the Modem card, CD-ROM, Floppy and HDD NOTE: There have the hook lock on CD-ROM, floppy and HDD cage, in other words, please move a little bit forward to release the lock then you can install these parts smoothly. 1. Insert the HDD to the bracket by following the instructions here. 2. Place the HDD module back to the original position. 3. Place the floppy drive back to the original position. 4. Place the CD-ROM drive back to the original position. 5. Connect the HDD power cable and IDE cable. 6. Connect the floppy cable and power cable. 58 Chapter 3 7. Connect the CD-ROM power, IDE and CD-In cables. 8. Place the modem card back to one PCI slot. Then secure the modem card with the screw. Installing the Cables 1. Connect the IDE1 and IDE2 cable to the motherboard. 2. Connect the floppy cable to the motherboard. 3. Connect the CD-In cable to the motherboard. 4. Connect the Aux-In cable to the motherboard. Chapter 3 59 Installing the Front Panel 1. Place the front bezel back to the original position. Closing the System 1. Place the side door back to the original position. 2. Secure the side door with the two screws as shown here. 60 Chapter 3 Chapter 4 Troubleshooting This chapter provides troubleshooting information for the Aspire T130: T Power-On Self-Test (POST) T Index of Error Messages T Index of Error Codes and Error Beeps T Index of Error Symptoms T Undetermined Problems Chapter 4 61 Power-On Self-Test (POST) Each time you turn on the system, the Power-on Self Test (POST) is initiated. Several items are tested during POST, but is for the most part transparent to the user. The Power-On Self Test (POST) is a BIOS procedure that boots the system, initializes and diagnoses the system components, and controls the operation of the power-on password ...