Votos - 3, Puntuación media: 5
(
)
)
|
Resumen del manual
Ethernet PC Car. What.s Insid. Hardware Description . LED Indicators . Hardware Installation . Software Driver Installation . EMI Certification . Pages 2 to . see this sid. . Pages 6 to . see this sid. . Specifications . Software Drivers . Technical Support . Hardware Descriptio. Accton.s Ethernet PC Card is a "feature-packed" credit card. sized adapter for PCMCIA-compliant personal computers. The card comes in two models (two media couplers to choos. from). . EtherPair-PCMCIA (EN2216-1. . EtherDuo-PCMCIA (EN2216-2. The EtherPair-PCMCIA has a single RJ-45 (10BASE-T) por. for unshielded twisted-pair connection, while the EtherDuo. PCMCIA has an RJ-45 and BNC (10BASE2) connector. This product features NE2000 compatibility. You can use th. provided drivers in the driver diskette or use standard NE200. network drivers. LED Indicator. The following LEDs are found on both the EtherPair-PCMCI. and EtherDuo-PCMCIA media couplers. Transmit/Receive LE. Color. Gree. Function. Monitors signals transmitted to and received fro. the network. The green LED labeled Tx/Rx lights up to indicate that th. Ethernet PC Card is transmitting or receiving signals from th. network. The rate of flashing is proportional to the amount o. network traffic. Link LE. Color. Gree. Function. Monitors link status of card's twisted-pai. connection. This LED lights up to indicate that a valid 10BASE-T link i. established. It is always on under normal operating conditions. If the LED is off after power is applied, check the RJ-45 port'. cable connection. Hardware Installatio. 1. Insert the Ethernet PC Card into the computer.s PCMCI. slot. Insert the card with the 68-pin connector facing th. PCMCIA slot and the label facing up. See Figure 1 fo. illustration. Figure 1. Inserting the Ethernet PC Card into the Type I. PCMCIA Slot. 2. Plug the media coupler into the card.s 15-pin connector. 3. Connect the media coupler to the network using either UT. or thin coax cabling. a. Connecting to the RJ-45 port using UTP cable. Figure 2. Connection Using UTP Cabl. (EtherPair-PCMCIA, model EN2216-1. b. Connecting to the BNC port with thin coax cable. Figure 3. Connecting to Thin Ethernet Cabl. (EtherDuo-PCMCIA, model EN2216-2. Note: If the card is attached to the end of the network segment. be sure a 50-Ohm terminator is installed on the open end of th. T-type connector. Software Driver Installatio. The diskette labled .Driver Diskette,. that comes with th. package contains all the software drivers available for th. Ethernet PC Card. A RELEASE.TXT file, describing th. contents of the diskette is found in the root directory. Differen. drivers are stored in separate subdirectories, which als. include a text file. Select the driver you need for your syste. and refer to the text file for the installation procedure. EMI Certificatio. FCC Class B Certificatio. Accton Technology Corporatio. Model Number: EN221. FCC ID: HEDEN221. This device complies with Part 15 of the FCC Rules. Operation i. subject to the following conditions. 1. This device may not cause harmful interference, an. 2. This device must accept any interference received, includin. interference that may cause undesired operation. Warning! This equipment has been tested and found to comply with th. limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection agains. harmful interference in a residential installation. This equipmen. generates, uses and can radiate radio frequency energy and, if no. installed and used in accordance with the instructions, may cause harmfu. interference to radio communications. However, there is no guarante. that interference will not occur in a particular installation. If this equipmen. does cause harmful interference to radio or television reception, whic. can be determined by turning the equipment off and on, the user i. encouraged to try to correct the interference by one or more of th. following measures. . Reorient or relocate the receiving antenna. . Increase the distance between the equipment and receiver. . Connect the equipment into an outlet on a circuit differen...
Otros modelos de este manual:Accesorios para el ordenador - EN2216-2 (314.5 kb)