Iniciar sesión:
Votos - , Puntuación media: ( )

Manual de usuario Adder Technology, modelo DDC Ghost

Fabricar: Adder Technology
Tamaño del archivo: 165.24 kb
Nombre del archivo: 72cfb689-3bd3-4b62-adfa-32fb9aa69eba.pdf

Idioma del manual:en

El documento se está cargando, por favor, espere
El documento se está cargando, por favor, espere

Resumen del manual


(b) Increase the separation between the equipment and the receiver. (c) Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. (d) Consult the supplier or an experienced radio/TV technician for help. Adder Corporation, Adder Asia Pacific 29 Water Street, 6 New Industrial Road, Newburyport, MA 01950, Hoe Huat Industrial Building United States of America #07-01, Singapore 536199 Tel: +1-888-932-3337 Tel: +65 6288 5767 Fax: +1-888-275-1117 Fax: +65 6284 1150 DDC Ghost User Guide The DDC Ghost module is designed to attach in-line with a VGA connection in order to present Extended Display Identification Data (EDID) to the video controller independently of the actual monitor, switch or extender unit. Video signals are passed straight through the DDC Ghost. The Extended Display Identification Data (EDID) information stored within the DDC Ghost can either be cloned from a monitor or used with a standard set of information (see Standard EDID Information). What’s in the box DDCGhostVGASTATUSCLONECOMPUTERMONITOR DDC Ghost module Optional Blue connector power (to computer) input Black connector Control button (to monitor) and indicator DDCGhostVGASTATUSORVideoCLONECOMPUTERMONITEDIDdatasignals Video cable (15 pin D-type male to 15 pin D-type male) What you may additionally need Mains to 5VDC power adapter (if power cannot be obtained from the controlling computer via the video cable) Adder P/N: PSU-IEC-5VDC Additional video cable (15 pin D-type male to 15 pin D-type male) Adder P/N: VSC18 Email: support@adder.com Web: © 2008 Adder Technology Limited • Release 1.0e • January 2008 • Part No. ADD0074 All trademarks are acknowledged. Documentation by Corporate Text & Design (Cloning EDID information The DDC Ghost module contains a default set of EDID values which may be used immediately with most monitors (see Standard EDID Information). Alternatively, you can use a ‘donor’ monitor from which you can clone new EDID information. To clone EDID information 1 Link the BLACK connector of the DDC Ghost to the donor monitor (diagram A). 2 Provide power for the DDC Ghost module in one of two ways, either: • Link the BLUE connector of the DDC Ghost to a computer video output for the duration of the cloning operation (diagram B), or • Attach the optional 5VDC power adapter to the socket on the side of the DDC Ghost module (diagram C). 3 Ensure that the donor monitor and the DDC Ghost module are powered. The DDC Ghost red STATUS indicator should be on. 4 Using a narrow implement, press and hold the recessed button labelled CLONE on the side of the module (diagram D). The STATUS indicator will begin to flash slowly for five seconds. Release the button while the indicator is still slowly flashing. • If new EDID information is available, it will be copied to the DDC Ghost module memory. • If there is no EDID information to clone then the existing DDC Ghost memory will be not altered. • If there is an error during cloning then the DDC Ghost will be automatically reset to its standard values. 5 When the operation is complete, the STATUS indicator will flash rapidly five times. Disconnect the DDC Ghost module from the donor monitor. Resetting EDID information If required, you can reinstate the standard EDID values (see Standard EDID Information) into the DDC Ghost module memory. To reset the EDID information 1 Ensure that the DDC Ghost is powered (either from the video output of a host computer or an optional power adapter) and check that the red STATUS indicator is on. 2 Using a narrow implement, press and hold the recessed button labelled CLONE on the side of the module (diagram D). The red STATUS indicator will flash slowly for five seconds and then will go off for a further five seconds. 3 Release the button while the red STATUS indicator is off, following the five slow flashes. The reset operation will take place and then the red STATUS indicator will flash rapidly five times to indicate a successful completion. DDCGhostVGASTATUSCLONECOMPUTERMONITORLink the computer to the BLUE connector B DDCGhostVGASTATUSCLONECOMPUTERMONITORLink the monitor to the BLACK connector A DDCGhostVGASTATUSCLONECOMPUTERMONITORIf power is unavailable from the computer via the BLUE connector, use the optional 5VDC power adapter C DDCGhostVGASTATUSCLONECOMPUTERMONITORPress and hold the recessed CLONE button. Release it as follows: To clone: While indicator is slowly flashing. To reset: While indicator is off (immediately following the slow flashes). D Installing for normal operation During normal operation, the DDC Ghost module supplies either standardised or cloned EDID information to the computer instead of the data from the connected monitor. To install for normal operation 1 Link the BLACK connector of the DDC Ghost to the monitor (diagram A). 2 Link the BLUE connector of the DDC Ghost to the computer video output (diagram B) Note: In operation, the red STATUS indicator should be o...

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría