Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
The 6-pin AGP Pro Power connector provides extra +5V and +3.3V power for AGP Pro VGA card. Make sure you plug in the right direction. 13 24-pin ATX Power connector 1 +12V +5V 5VSB +5V PWR OK -5v AGP Pro Power COM COM +5V COM COM COM 61 +5V PS-ON COM COM +3.3V -12V +3.3V +5V GND GND +3.3V +3.3V +3.3V GND 20 19 8. Connecting Redundant SPS Connector This motherboard implements Redundant SPS connector to provide better expansibility on superior server. It is feasible to install an additional 337-watts power supply module (optional) in a hot-swappable redundant configuration, which enables a fully-configure system to continue running even if one power module fails. PS_ON PS 3 Fail Fan 3 Fail I2CDA Present 3 GND 14 13 Present 1 I2C CLK Fan 1 Fail PS 1 Fail 1 2 PS 2 Fail Fan 2 Fail Present 2 5VSB 9. Connecting IDE & FDD Cable Connect 34-pin floppy cable and 40-pin ATA66 or ATA33 IDE cable to floppy connector FDC and IDE connector IDE1, IDE2. Pin1 of cable is normally marked with red color. Be careful of the pin1 orientation. Wrong orientation may cause system damage. IDE2 (Secondary) IDE1 (Primary) Primary Master (1st) Primary Slave (2nd) Secondary Slave (4th) Secondary Master (3rd) FDD Connector ATA/66 IDE Connector Pin 1 10. Connecting 68-pin Ultra3 SCSI Cable (DX34 Plus) 12. CD-IN & FAX-Voice Connector (Applied to DX34) The DX34Plus provides two 68-pin Ultra Wide/Ultra 2/3 SCSI connectors for 16-bit If you have installed the CD-ROM drive in the or 16-bit differential SCSI devices. system, the CD-In Connector (CN19) can be connected to audio output connector of internal CD-ROM drive. 68-pin SCSI Ultra3 Connectors This FAX-VOICE connector (CN21) can let the fax sound of Modem device speak out from external speaker by connected .to internal Modem card. Pin4 -Right --Phone 11. Connecting Front Panel Connector 13. Connecting SCSI LED Connector Attaching such as power LED, reset switch, power switch connector, etc.… corresponding pins. to The 4-pin SCSI LED connector can be connected to the SCSI hard disk control card activity LED connector. Read or write activity by devices connected to the SCSI card ATX Chassis will cause the LED lighting up. Power Switch Power LED Intrusion Switch 1 21 2 22 CN23 HDD LED Reset Switch +5V CN24 GND PWR LED RST S/W +5VSB INT S/W 1 21 2 22 GND GND +5V GND HDD LED HDD LED +5V - + + - - + + - 14. Select Buzzer or Ext. Speaker 16. Power-On and Load BIOS Setup After you finish the setting of jumpers and connect correct cables. Power on and There is one jumper cap over pin1 and pin2 of JP4 for internal buzzer. If you want to enter the BIOS Setup, press during POST (Power On Self Test). Choose use external case-mounted speaker instead of internal buzzer, please remove jumper "Load Default Setting" for recommended optimal performance. cap to short pin2 and pin3. 1 JP4 1 Buzzer Speaker (Default) Del Warning: Please avoid of using "Load Turbo Defaults", unless you are sure your system components (CPU, DRAM, HDD, etc.) are good ...
Accesorios para el ordenador - DX34 PLUS (1.37 mb)
Accesorios para el ordenador - DX34 (1.37 mb)
Accesorios para el ordenador - DX34 PLUS (1.37 mb)