Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
So in this manual. of publication, all Disclaimer This manual is intended only as a instructions on installing your motherboard come with your components and drives. SLK2650-BQE - Quiet Black Mid Tower Case Your new case features a super-quiet 350 with a main power switch. Make sure you turn position before you boot up your computer for the won't need to switch to the OFF (O) position, since soft on/off feature. This lets you turn your computer soft switch on your computer case. If your computer crashes shut it down using the soft switch, you can switch the main (O) position. [ Applies only to models designed for sale in the European Union: Solution Series Power Supply models designed for the EU include Power Factor Correction (PFC) circuitry in accord with European standard regulation code EN61000-3-2. By altering the input current wave shape, PFC improves the power factor of the power supply. This results in increased energy efficiency, reduced heat loss, prolonged life for power distribution and consumption equipment, and improved output voltage stability.] Setting Up 1. Place the case upright on a flat, stable surface. The power supply fan should be at the back, facing you. Note (not applicable to models designed for the European Union): Before installation, check the red voltage switch setting on the power supply. It should match your local voltage (115V for North America, Japan, etc. and 230V for Europe and many other countries). If it doesn't match, please change the setting. If you don't, you could damage your equipment and void your warranty. 2. Remove the screws from the right side panel. Grip the panel at the finger-grip indent and slide it towards you to open the case. 3. Inside the case you should see the power supply, some wiring with marked connectors (USB, PWR etc.), an installed I/O panel and a power cord. You will also find an expansion slot protective cover mounted above the expansion slots. 4. In order to install expansion cards, remove the protective cover by pressing the tab on the cover. Note: Inside this cover, you'll find a compartment marked "hardware." Inside this compartment, you can store hardware or small tools (screws, brass standoffs, plastic stands, etc.) 1 Installing This manual consult your motherboard troubleshooting. 1. Lay the case down, with power supply should be 2. Make sure you have the correct panel provided with the case board manufacturer for the correct 3. Line up your motherboard with the holes are lined up. Not all motherboards holes; this is normal, and won't affect functionality. will likely be extra holes.) 4. Remove your motherboard by lifting it up. 5. Screw the brass standoffs into the threaded holes motherboard. Do not overtighten the standoffs. Some pre-installed for your convenience. 6. Place your motherboard on the brass standoffs. 7. Screw in your motherboard to the standoffs with the provided screws. Your motherboard is now installed. Connecting the Power and LED The Antec Solution Series SmartPower power supply is an ATX12V power supply with a single 20-pin Main Power Connector, a 6-pin AUX Connector, and a 4-pin +12V Power Connector for the motherboard. It also includes 2 SATA connectors, five to seven 4-pin Peripheral Power Connectors and one to two 4-pin Floppy Drive Power Connectors for your drives. It is backwards compatible to previous ATX form factor power supplies. If your motherboard does not support the AUX Power Connector or the +12V Power Connector, you can still use this power supply. The power supply is also equipped with a 3-pin fan signal connector. Connect it to one of the fan connectors on your motherboard. You may monitor the speed of the rear power supply fan through your motherboard BIOS or through the monitoring software that's supplied with your motherboard. Note: At low temperatures, the fan may run as slow as 1200 RPM. At these speeds, some motherboards may not properly detect the fan speed and may generate false warnings of fan failure. To ensure proper monitoring of the fan, please check your motherboard manual. 1. Connect the 20-pin ATX power connector (and AUX or +12V connectors if appropriate) to your motherboard. 2. Connect the Reset switch (labeled RESET SW) to your motherboard at the RST connector. Make sure the label always faces the front of the case. 3. Connect the Power Switch (labeled POWER SW) to the PWR connector on your motherboard. 4. You'll find the Speaker connector (labeled SPEAKER) behind the PWR connector. 5. The Power LED, Hard Drive LED, LED I & LED II connectors all share a single ribbon cable. Attach the Power LED (labeled POWER) and HDD LED 2 connectors the LED I and etc. or any other and peripherals. Connecting the USB Ports You'll find two 5-pin internal the front USB connectors. Note: If you want to use both front and the 8-in-1 card reader, your headers. Here's how to connect the internal USB 1. Check the USB pin layout in your motherboard it follows this standard pin out: Pin 1: USB Power - ...