Votos - 3, Puntuación media: 3.3
(
)
)
|
Resumen del manual
This is an Intel standard connector, which is keyed so that it can’t be accidentally reversed as long as it is connected to a proper Intel standard motherboard header. Connect the 10-pin connector to your motherboard header so that the blocked pin fits over the missing header pin. Note: Please check your motherboard manual for your IEEE 1394 header pin layout and make sure it matches the attached table. If you intend to connect the front FireWire port to an IEEE 1394 add-on card that comes with an external-type IEEE1394 connector, please call Antec customer service at (800) 22ANTEC (North America) or +31 (0) 10 462-2060 (Europe) to buy an adapter. This adapter will allow you to connect the front IEEE 1394 port to the external-type connector. Standard Pin Assignment for IEEE 1394 Connector 1 2 109 Pin Signal Names Pin Signal Names 1 TPA + 2 TPA 3 Ground 4 Ground 5 TPB + 6 TPB 7 +12V (Fused) 8 +12V (Fused) 9 Key (No pin) 10 Ground CONNECTING THE AUDIO PORTS Locate the internal audio connectors from your motherboard or sound card. Consult your motherboard or sound card manual for the pin-out positions. 1. Microphone Signal Pin: Connect the MIC-IN connector to this pin. 2. Microphone Power: Connect the MIC-POWER connector to this pin. 3. Ground Pin: Connect the GROUND connector to this pin. 4. Front Right Speaker Out Pin: Connect the R-OUT connector to this pin. 5. Front Right Speaker Out Pin: Connect the L-OUT connector to this pin. 6. Rear Right Speaker Out Pin: Connect the R-RET connector to this pin. 7. Rear Left Speaker Out Pin: Connect L-RET connector to this pin. Note: If your motherboard is not equipped with REAR SPEAKER output, it is not necessary to use the R-RET and L-RET connectors. DRIVE INSTALLATION Minuet incorporates a rapid-release Flip Up Drive Cage for easy drive installation. The Cage includes three drive bays: one external 5.25”, one external 3.5”, and one internal 3.5”. 1. Before installing the external drives, remove the external drive bay covers. a. To remove the external 5.25” drive bay cover, face the front of the case and use your left hand thumb to press firmly on the LEFT or outside edge of the left bay cover to release it. (See picture 3) b. To remove the external 3.5” drive bay cover, face the front of the case and use your right hand thumb to press firmly on the RIGHT or outside edge of the right bay cover to release it. (See picture 4) 4 2. Lift up and slide the drive cage from the case. 3. Place the cage upside down on a fl at surface. 4. Note: You must install the external devices first, before installing the internal 3.5” device. 5. Slide the external 5.25” device into the drive cage from the front. Since the drive cage is upside down, your drive should be too so that it will be properly orientated once the cage is installed in the Minuet II. 6. Align the bottom rear screw holes (one at each side) on the device with the two screw holes (the pair closest to the front of the cage) on the cage and fasten the device with the screws provided. (See picture 5) 7. Slide the external 3.5” device into the drive cage from the front. Since the drive cage is upside down, your drive should be too so that it will be properly orientated once the cage is installed in the Minuet II. 8. Align the bottom rear screw holes (one at each side) on the device with the two screw holes on the cage and fasten the device with the screws provided. (See picture) 9. To install the internal 3.5” device, find the two mounting prongs on one side of the bay. With one hand holding the device at a 45-degree angle with the bottom side up, align the two screw holes on one side of the device with the prongs and slide the device into the bay. (See picture 7) 10. Fasten the other side of the device to the two tabs with the screws provided. (See picture 8.) 11. When sliding the Cage back into the case, work slowly and carefully to ensure that the front panels of the external devices align properly with the holes provided for them in the bezel. 12. Connect power to each of the devices. COOLING SYSTEM Th e TriCool fan The case includes one 80mm TriCool fan installed in the side of the chassis. This fan has a three-speed switch that lets you choose between quiet, performance, or maximum cooling. We set the default fan speed to “Medium”. (See specifi cations below) The fan is installed so that the air is blowing out of the case. Connect a large 4-pin connector from the power supply to the male 4-pin connector on the fan. Note: The minimum voltage to start the fan is 5V. We recommend our users to set the fan speed to High if you choose to connect the fan to a fan control. A fan control device regulates the fan speed by varying the voltage to it. The voltage may start as low as 4.5V to 5V. Connecting a TriCool set on Medium or Low to a fan-control device may result in the fan not being able to start. The already lowered voltage from the fan control device will be further reduced by the TriCool circuitry below 5V. 5 Specifi ca...