Votos - 1, Puntuación media: 4
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
Lower HDD Installation 1. Remove the thumbscrew holding the lower HDD cage. 2. Pull the HDD cage from its position by pulling the ring towards you. 3. There are two HDD trays inside the cage. Squeeze the metal clips on each side of the tray and slide the tray out. 4. Mount your hard drive into the drive tray with the special screws provided. Don’t over-tighten the screws as this will reduce the vibration and noise dampening ability of the silicone grommets. Note: Always mount the HDD with the thicker side of the silicone grommets facing up. 5. Slide and lock the tray back into the cage. 6. Slide the cage back to the case and fasten the thumbscrew. 7. Find the right connector on the power supply and connect it to the hard drive. 8. Repeat the same procedure for the other drives. 4 Cooling System The Rear 120mm TriCool™ fan: This case comes with one 120mm TriCool rear fan installed. This fan has a three-speed switch that lets you choose the speed that best suits your needs. The default setting is Low. See the following specifications. 120mm TriCool Fan Size: 120 x 120 x 25.4mm TriCool Fan Rated Voltage: DC 12V Operating Voltage: 10.2V ~ 13.8V Speed Input Current Air Flow Static Pressure Acoustical Noise Input Power High 2000 RPM 0.24A (Max.) 2.24 m. / min (79 CFM) 2.54 mm-H2O (0.10 inch-H2O) 30 dBA 2.9 W Medium 1600 RPM 0.2A 1.59 m. / min (56 CFM) 1.53 mm-H2O (0.06 inch-H2O) 28 dBA 2.4 W Low 1200 RPM 0.13A 1.1 m. / min (39 CFM) 0.92 mm-H2O (0.04 inch-H2O) 25 dBA 1.6 W The Top 200mm TriCool™ Fan The Mini P180 comes with a 200 x 30mm TriCool fan. This fan has a three-speed switch that lets you choose the speed that best suits your needs. The default setting is Low. See the specification below: 200mm TriCool Fan Size: 200 x 200 x 30mm TriCool Fan Rated Voltage: DC 12V Operating Voltage: 10.2V ~ 13.8V Speed Input Current Air Flow Static Pressure Acoustical Noise Input Power High 800 RPM 0.3A (Max.) 3.799 m. / min (134.11CFM) 0.688 mm-H2O (0.027 inch-H2O) 29.4 dBA 3.6 W Medium 600 RPM 0.17A 3.07 m. / min (108.493 CFM) 0.397 mm-H2O (0.016 inch-H2O) 26.5 dBA 2.04 W Low 400 RPM 0.08A 2.34 m. / min (82.612 CFM) 0.197mm-H2O (0.008 inch-H2O) 23.6 dBA 0.96 W The External fan Control: There are two external fan switches on the rear of the case near the top. They allow you to adjust the speed of these two fans without having to open the case. Note: The minimum voltage to start these fans is 5V. We recommend our users to set the fan speed to High if you choose to connect the fan to a fan control device or to the Fan-Only connector found on some Antec power supplies. A fan-controller regulates the fan speed by varying the voltage to it. The voltage may start as low as 4.5V to 5V. Connecting a TriCool set on Medium or Low to a fan-control device 5 may result in the fan not being able to start. The already lowered voltage from the fan controller will be further reduced by the TriCool circuitry below 5V. We recommend setting these fans to Low speed to maximize quiet computing. The Optional Fans There are two optional 120mm fan mounts at the front of the case inside the HDD cages. These two fan mounts are designed to enhance the CPU or VGA card cooling. However, you will need to remove the HDD cage (as a result of sacrificing two or three HDD bays depending on which cage to be removed) should you choose to use the fan mount in it. In order to build a quieter system we recommend NOT installing the optional fans. The Washable Air Filters There are two filters located behind the front grills and one filter inside the lower chamber. From time to time it will be necessary to wash the installed air filters. Not washing the air filters will result in higher system temperatures and possible stability problems. We recommend checking the air filters at least once a month initially. The frequency will depend on system usage (users whose systems run 24/7 will likely have to check/wash more often than those who don’t use their systems every day) and on environmental conditions. To remove the front filters: 1. Push one of the fan grills at the right middle edge to open the grill . 2. There are two tabs on the filter. To remove the filter use both your hands, grip the tabs and slide it towards the center, tag it outwards and lift out. To remove the bottom filter: 1. Grasp the locking tab and gently push it towards the center of the filter. 2. Tug the filter away from the case and then slide it out. For more useful suggestions and advice on building this case please visit Antec’s FAQ’s on 6 Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 USA tel: 510-770-1200 fax: 510-770-1288 Antec Europe B.V. Stuttgartstraat 12 3047 AS Rotterdam The Netherlands tel: +31 (0) 10 462-2060 fax: +31 (0) 10 437-1752 Customer Support: US & Canada 1-800-22ANTEC customersupport@antec.com Europe +31 (0) 10 462-2060 europe.techsupport@antec.com © Copyright 2008 Antec, Inc. All rights reserved. All trademarks are the property of their respec...
Otros modelos de este manual:Accesorios para el ordenador - Mini P180 White (78.77 kb)