Votos - 4, Puntuación media: 4.3 ( )

Fabricar: Antec Tamaño del archivo: 456.3 kb Nombre del archivo: 58ac9f12-65b5-475e-bc54-a93ff54a1bd4.pdf Idioma del manual:

Note: At low temperatures, the fan may run as slow as 950RPM. At these speeds, some motherboards may not properly detect the fan speed and may generate false warnings of fan failure. To ensure proper monitoring of the fan, please check your motherboard manual. POWER SUPPLY AIR DUCT There is a special duct leading from the front of the chassis to the power supply. This design is in place to keep the power supply quieter by providing the power supply with its own source of air separate from the rest of the system. The power supply will draw air in from the front of the case and exhaust it out the rear. SIDE VENTS There are vents on the left side of the rackmount. In an open rack environment, they increase the airflow in the system by allowing more fresh air into the system when necessary. If you are keeping your rackmount in a cabinet where environmental air circulation is not as good as open Picture 1 For 24-pin motherboards Picture 2 For 20-pin motherboards 2 rack, please use the clear plastic film that came with the toolbox to cover the ventilation (see picture 3). This can prevent hot air in the cabinet from entering the system and causing heat related system problems. CONNECTING THE USB PORTS You will find two 4-pin connectors on cables attached to the front USB ports. Connect the 4-pin connectors to your motherboard headers so that the USB Power pins match the VCC pins on the connectors. Note: Please check your motherboard manual for your USB header pin layout and make sure it matches the attached table. If it does not match, please call Antec customer support at (800) 22ANTEC (North America) or at +31 (0) 10 462-2060 (Europe) to buy a USB adapter. This adapter will allow you to connect the front USB to your motherboard on a pin-by-pin basis. Intel Standard USB Header Pin Layout Pin Signal Names Pin Signal Names 1 USB Power 1 2 USB Power 2 3 Negative Signal 1 4 Negative Signal 2 5 Positive Signal 1 6 Positive Signal 2 l Ground 1 8 Ground 2 9 Key (No Pin) 10 Empty Pin 1 2 □ о О о О о о о о 9 10 CONNECTING THE IEEE 1394 (FIREWIRE®, I.LINK®) PORT You will find a single 10-pin connector on a cable attached to the front IEEE 1394 connection. This is an Intel standard connector, which is keyed so that it can’t be accidentally reversed as long as it is connected to a proper Intel standard motherboard header. Connect the 10-pin connector to your motherboard header so that the blocked pin fits over the missing header pin. Note: Please check your motherboard manual for your IEEE 1394 header pin layout and make sure it matches the attached table. If you intend to connect the front FireWire port to an IEEE 1394 add-on card that comes with an external-type IEEE1394 connector, please call Antec customer support at (800) 22ANTEC (North America) or +31 (0) 10 462-2060 (Europe) to buy an adapter. This adapter will allow you to connect the front IEEE 1394 port to the external-type connector. 1 2 □ o o o o o o o o 9 10 Standard Pin Assignment for IEEE 1394 Connector Pin Signal Names Pin Signal Names 1 TPA+ 2 TPA- 3 Ground 4 Ground 5 TPB+ 6 TPB- l + 12V (Fused) 8 + 12V (Fused) 9 Key (No Pin) 10 Ground Picture 3 3 3.5” DEVICE INSTALLATION With the front bezel facing you, turn the latch and swing the front door. You can see there are two 5.25” and two 3.5” external drive bays. Inside the case there are four 3.5” drive cages. For external 3.5” devices: 1. Locate the external 3.5” drive bays. They are to the right of the 5.25” drive bays. 2. Unscrew the 4 small Phillips head screws located on the front panel around the drive cage. 3. Pull the cage and unscrew the drive bay covers. 4. Install your external 3.5” devices. 5. Reattach the cage and devices to the chassis. Note: Don’t take off the covers and plates for the drive bays that you are not using now For Internal devices: 6. Loosen the thumbscrews on each side of the drive bay, for the drive bay that you wish to install a device. 7. Pull the drive tray forward all the way out of the chassis. 8. Mount your hard drive or other internal 3.5” device into the drive tray through the bottom rubber grommets with the special screws provided (see picture 4). Note: Don’t over-tighten. Over-tightening the screws will harm the vibration—and noise-reducing ability of the rubber grommets. 9. Slide the tray/device assembly back into the chassis and retighten the picture 4 thumbscrews. 10. Repeat the above as necessary. 11. Connect either a large 4-pin connector or SATA power connector from the power supply to the male 4-pin connector or SATA connector on each of the other devices. 5.25” DEVICE INSTALLATION 1. Unscrew the two screws on the left side of chassis. Unscrew the four screws around the front of the 5.25” drive bays (along the top and right sides of the cage). 2. Pull the cage towards the back of the case and then lift the cage out. 3. Unscrew the screws that attach the drive bay cover to the cage. 4. Install your 5.25...

Descargar ahora

Introduzca dos números de la imagen: