Votos - 3, Puntuación media: 3.3
(
)
)
|
Resumen del manual
You can tuck or route excess cables in this compartment. 1. Open the right side panel as described in section 2.1. 2. Locate the cable management compartment with cable ties located behind the walls of the 3.5” drive cage. 3. Tuck or route your excess cables to the compartment. This will keep the cables from interfering with airflow in your case and help with cooling. 4. Use the cable ties provided to hold them in place. 2.4 MOTHERBOARD INSTALLATION 1. Lay the case down, with the open side facing up. The drive cages and power supply should be visible. 2. Make sure you have the correct I/O panel for your motherboard. If the panel provided with the case isn’t suitable, please contact your motherboard manufacturer for the correct I/O panel. 3. Align your motherboard with the standoff holes and remember which holes are lined up. Not all motherboards will match with all the provided holes; this is normal and won’t affect its functionality. 4. Remove your motherboard by lifting it up. 5. Install standoffs as needed and put the motherboard back in. 6. Screw in your motherboard to the standoffs with the provided Phillips-head screws. Note: The Two Hundred comes with a CPU cutout on the motherboard tray, which will allow you to change your CPU heatsink without removing the motherboard. 5 2.5 INTERNAL 3.5” DEVICE INSTALLATION The Two Hundred provides space for up to six 3.5” hard drives. Before you begin, remove the side panels and front bezel of the case as described in section 2.1. Behind the front bezel there is a fan cage which provides space for up to two fans at the front of the case. 1. Open the fan cage by pressing both clips to release it, then swing it open and detach it from the chassis. 2. Insert your 3.5” device into the 3.5” drive cage from the front of the case until the mounting holes align with the screw holes in the cage. 3. Fasten the device in place with the provided screws. 4. Mount any other 3.5” HDD devices accordingly. 5. Connect the appropriate power and data cables to the device(s). 6. Replace the fan cage. 2.6 FRONT-LOADED HOT SWAP SATA HARD DRIVE CADDY This case comes with a built-in, externally accessible 3.5” SATA drive bay where you can load/unload your drive without shutting down your computer. Note: Before you can use the hot swap feature, you must install all related drivers that come with your motherboard and turn on the “AHCI” function in the BIOS to activate the hot swap feature. Loading: 1. Align your SATA HDD with the drive bay with the connector facing the case. 2. Push the HDD all the way into the bay until it locks into position. Unloading: 1. Ensure that your HDD is not in use. 2. Push the release button on the left-hand side of the drive bay and pull the HDD free. 6 2.7 EXTERNAL 5.25” DEVICE INSTALLATION There are three externally accessible 5.25” drive bays. Before you begin, remove both side panels and front bezel as detailed in section 2.1. 1. Remove the drive bay faceplate by applying pressure to the inside of the plate until it pops free of the bezel. 2. Slide your 5.25” device into the bay from the front of the case. 3. Secure the drive into position in the drive cage using the provided screws. 4. Mount any other 5.25” devices accordingly. 5. Connect the appropriate power and data cables to your device(s). CONNECTING THE FRONT I/O PORTS 3.1 USB 2.0 Connect the front I/O panel USB cable to the USB header pin on your motherboard. Check the motherboard user’s manual to ensure that it matches the table below: 12 Pin Signal Names Pin Signal Names 1 USB Power 1 2 USB Power 2 3 Negative Signal 1 4 Negative Signal 2 5 Positive Signal 1 6 Positive Signal 2 7 Ground 1 8 Ground 2 9 Key (No Connection) 10 Empty Pin 9 10 3.2 AC’97 / HD AUDIO PORTS There is an Intel® standard 10-pin AC’97 connector and an Intel® 10-pin HDA (High Definition Audio) connector linked to the front panel of the case. 10 642 97531 Pin Signal Names (HDA) Pin Signal Names (AC’97) 1 MIC2 L 1 MIC In 2 AGND 2 GND 3 MIC2 R 3 MIC Power 4 AVCC 4 NC 5 FRO-R 5 Line Out (R) 6 MIC2_JD 6 Line Out (R) 7 F_IO_SEN 7 NC 8 Key (no pin) 8 Key (no pin) 9 FRO-L 9 Line Out (L) 10 LINE2_JD 10 Line Out (L) 7 You can connect either the AC’97 or the HDA connector, depending on your motherboard. Locate the internal audio connectors from your motherboard or sound card and connect the corresponding audio cable. Consult your motherboard or sound card manual for the pin-out positions. Even if your system supports both standards, only use one connector. 3.3 POWER SWITCH / RESET SWITCH / HARD DISK DRIVE LED CONNECTORS Connected to your front panel are LED and switch leads for power, reset, and HDD LED activity. Attach these to the corresponding connectors on your motherboard. Consult your motherboard manual for specific pin header locations. For LEDs, colored wires are positive ( + ). White or black wires are negative ( – ). If the LED does not light up when the system is powered on, try reversing the connection. For more information on ...