Votos - 3, Puntuación media: 3.3
(
)
)
|
Resumen del manual
PSU screws (10) B. Motherboard standoffs (3:4 preinstalled) C. Motherboard screw (9) D. 5.25”/2.5” optional drive screw (10) E. Front panel fan screws (2) F. Drive bay rails for 3.5” (5 pairs) G. Zip ties (2) H. Standard fan screws (4) A H G F E D C B Section 2 Hardware Installation One / One S / One S3 User Manual 2.1 Setting Up When working in your case, please keep the following in mind: . Put the case upright on a flat, stable surface so that the rear panel (power supply and expansion slots) is facing you. . Handle all components and cards with care. . To avoid electrostatic discharge, ground yourself periodically by touching an unpainted metal surface or by using a wrist grounding strap. . Before you connect a cable, ensure that both connectors are correctly aligned and oriented. . Do not sit on your chassis. Although it is constructed of heavy-duty steel and internally reinforced, it is not designed to support the weight of an adult, and may buckle. . Do not use your fingernails to separate edges or lift the sides of the chassis, as paint chipping or injury may occur. . Place the panel thumbscrews aside in a safe place. . Exercise caution and control when handling chassis interiors. We strongly recommend taking the appropriate time and care when working inside the chassis. Avoid hurried or careless motions. 2.2 Removing the Side Panels and Front Bezel To remove the left and right side panels: 1. Remove each set of two thumbscrews. 2. Slide the panel you want to remove toward the back of the case approximately 2 cm until it stops. 3. Pull the panel free of the chassis. You need to remove the front bezel in order to access the air filters and conduct maintenance. To remove the front bezel: 1. Grip the bezel by the bottom and pull forward. The bezel will pop free of the chassis. IMG_0982 2.3 Motherboard Installation Before proceeding, check the manual for your CPU cooler to find out if there are steps you must do before installing the motherboard. Make sure you have the correct I/O panel for your motherboard. If the panel provided with the chassis isn’t suitable, please contact your motherboard manufacturer for the correct I/O panel. Make sure you have the correct I/O panel. This case comes with 5 preinstalled motherboard standoffs. These are positioned for Standard ATX motherboards but can be relocated to accommodate other form factors. 1. Align the motherboard with the standoff holes on the motherboard tray and remember or mark which holes are lined up. 2. Install standoffs as needed and put the motherboard in. 3. Screw your motherboard into the standoffs with the provided motherboard mounting screws. 2.4 Installing KUHLER H2O Liquid Coolers The following instructs how to install the Antec KUHLER H2O liquid CPU cooler (620 / 920). For any other CPU coolers, please consult your manufacturer’s installation guide. Caution: Check your motherboard’s CPU socket to ensure its compatibility with the KUHLER H2O. The KUHLER H2O 620 / 920 is compatible with the following CPU sockets: Intel® LGA 1155 / 1156 / 1366 / 2011* AMD® AM2 / AM3 / AM2+ / AM3+ *Your unit may not contain the LGA 2011 mounting bracket. To receive this bracket, please contact Antec customer support (information is listed at end of manual). **Be sure to install the KUHLER H2O with the end of the tubes positioned at the bottom of the radiator. 1. Remove the rear fan by unscrewing the fan from the back of the chassis. 2. Preparing the KUHLER H2O backplate is specific to your CPU socket. Please refer to the KUHLER H2O installation guide, available at (KUHLER H2O 620) or (KUHLER H2O 920) for more information. 3. Prepare the retention ring according to the CPU socket you’re using. 4. Complete installation according to the KUHLER H2O instructions. 2.5 Power Supply Installation 1. With the case upright, place the power supply in the case and align the rear of the unit with the mounting holes. 2. Attach the power supply to the case with the screws provided. Attach the power supply with the provided screws. 2.6 External 5.25” Device Installation The One / One S / One S3 can support up to three 5.25” devices. 1. Remove the side panels and front bezel as directed in Section 2.2. 2. Remove the drive bay cover by pressing out on the two small tabs on either side of the cover, then pushing the cover into the front of the bezel. 3. Replace the front bezel on the front of the chassis. 4. Slide your 5.25” drive through the front of the chassis until it lines up flush with the front bezel. You will feel the drive lock into position. 5. If you need more clearance on the inside of the chassis for your drive, pull the drive bay tab on the inside of the chassis toward you and push the drive in further. Note: You can optionally secure your drive with screws for extra stability (D in Section 1.3) Press down on the drive cover tabs. Remove the drive b...
Otros modelos de este manual:Accesorios para el ordenador - ONE (866.09 kb)
Accesorios para el ordenador - ONE S (866.09 kb)