Votos - 4, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Make sure If the panel provided is manufacturer 3. Line up motherboard holes, and determine remember where they Not all motherboards SLK3700AMB - Super Mid Tower Case Power Supply The power supply installed in this case Make sure you turn the switch to the ON ( I ) position before you boot up your computer In normal operation there is no need to turn power supply is equipped with a soft on/off feature which turns your computer on and off through the soft switch on your computer case. You may occasionally need to turn the switch to the OFF position should your computer crash use of the soft switch. [Applicable only to models designed for sale in the European Union: Solution power supply models designed for the EU include Power Factor Correction accord with European standard regulation code EN61000-3-2. By altering the input current wave shape, PFC improves the power factor of the power supply and energy efficiency, reduced heat loss, prolonged life for power distribution and consumption equipment, and improved output voltage stability. ] Note ( not applicable to models designed for the European Union): Check the red power supply voltage switch setting before installation. It should be the same as your local power voltage (115V for North America, Japan, etc. and 230V in Europe and many other countries). Change the voltage setting if necessary. Failure to take this precaution could result in damage to your equipment and could void your warranty. Set Up 1. Take the case out of the box. 2. Remove the Styrofoam. 3. Remove the plastic bag. 4. Place the case upright on a stable flat surface with the power supply fan at the back facing you . 5. Remove the screws from the right side panel. 6. There are two latches on the side panel. Press the latch release on each. The latches will pop up to about 65 degrees. Push the latches out to the 90 degree position to fully disengage the latches and swing open the panel. 7. Inside the case you should see the power supply, some wiring with marked connectors (USB, PWR etc.), an installed I/O panel, a power cord. You will also find a bag of hardware (drive rails, screws, brass standoffs, plastic stands, etc.) 8. Place the case with the front bezel facing you and press the release tabs on the bottom of the bezel to remove the front bezel. Set the bezel aside in a safe place. Motherboard Installation This manual is not designed to cover CPU, RAM, or expansion card installation. Please consult your motherboard manual for specific mounting instructions and troubleshooting. 1. Lay the case down so that the open side is up. You should be able to see the drive cage and power supply. 1 screw holes, and this is (In other words there will likely be extra holes.) Some standoffs may be pre-installed for 4. Lift up and remove your motherboard. 5. Screw in the brass standoffs to the threaded holes that line 6. Place your motherboard on the brass 7. Screw in your motherboard to the standoffs with the provided Phillips-head screws. 8. Your motherboard is now installed. Power/LED Connections The Antec Solution Series SmartPower power supply is ATX12V form factor power supply. An ATX12V power supply has a single 20-pin Main Power Connector, a 6-pin AUX Power Connector, and a 4-pin +12V Power Connector for the motherboard. It also comes with five to seven 4-pin Peripheral Power Connectors Drive Power Connectors for your drives. It is backwards compatible to previous ATX form factor power supplies. If your motherboard does not support the AUX Power Connector or the +12V Power Connector, you can still use this power supply. The power supply is also equipped with a 3-pin fan signal connector. Connect it to one of the fan connectors on your motherboard. You may monitor the speed of the rear power supply fan through your motherboard BIOS or through the monitoring software with your motherboard. Note: The speed of the fan may be as low as 1500 RPM when temperatures are low. At these speeds some motherboards may not be able to properly detect the fan speed and may generate false warnings of fan failure. Please refer to your motherboard manual for proper fan monitoring set up. 1. Connect the 20-pin ATX power connector (and AUX or +12V connectors if appropriate) to your motherboard. 2. Reset switch (labeled RESET SW) connects to your motherboard at the RST connector. The label should be facing the front of the case, and for all of the following connectors as well. 3. Power Switch (labeled POWER SW) connects to the PWR connector on the motherboard. 4. Speaker connector (labeled SPEAKER) is behind the PWR connector. 5. The Power LED, Hard Drive LED, and LED I & LED II connectors all share a single ribbon cable. Attach the Power LED (labeled POWER) and HDD LED connectors to the appropriate headers on your motherboard. The LED I and LED II connectors may be used as you see fit for such purpose as SCSI LED, Message LED, etc. as supported by your motherboard, expansion cards, and peripherals. USB Connection There...