Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Ensure that the drive cage is correctly assembled: a. Verify that the 1 x 2 backplane is connected to the edge of the auxiliary SCSI backplane via a 100-pin connector. b. Verify that the auxiliary SCSI backplane is inserted into the enclosure on the side of the cage and secured with one screw. c. Verify that the 1 x 2 backplane is secured to the back of the cage with four screws. d. Verify that a drive rail is attached to each side of the drive cage. 2. Insert the drive cage into the empty peripheral drive bay until the clips on the drive rails snap into the sides of the peripheral drive bay (see Figure 1). )LJXUH,QVWDOOLQJWKH'ULYH&DJH ,QVWDOOLQJWKH,&([WHQVLRQ&DEOH To install the I2C extension cable, perform the following steps: 1. Disconnect the I2C cable from the 20-pin connector on the system board and set it to one side (see Figure 2). drive rail clip drive cage 4 Dell PowerEdge 6300 and 4300 Systems 1 x 2 Backplane Installation Information 2. In the customer kit, locate the I 2C extension cable. (This cable has three connectors: a 20-pin connector on one end and in the middle and a 10-pin connector on the other end.) 3. Attach the 10-pin connector on the I 2C extension cable to the 10-pin connector on the 1 x 2 backplane. 4. Attach the 20-pin connector on the I 2C extension cable to the 20-pin connector on the system board. 5. Attach the loose end of the I 2C cable, which was set aside, to the middle connector of the I2C extension cable. 6. Attach a four-wire power cable to the power connector on the 1 x 2 backplane. NOTE: The four-wire power cable is the standard cable found on all systems and provides power to peripherals; for example, for a CD-ROM drive or tape drive. )LJXUH,QVWDOOLQJWKH, &([WHQVLRQ&DEOH 10-pin connector on 1 x 2 backplane I2C extension cable hard-disk drive SCSI backplane I2C cable 20-pin connector on system board power connector Dell PowerEdge 6300 and 4300 Systems 1 x 2 Backplane Installation Information5 ,QVWDOOLQJWKH6&6,&DEOH NOTE: The SCSI cable installation described in this document is a typical installation of the SCSI cable used with the 1 x 2 backplane. You can install the SCSI cable differently, depending on redundant arrays of independent disks (RAID) configurations and the existence of SCSI peripheral cards. Refer to your operating system documentation for information on how to set up your SCSI devices. To install the SCSI cable to the 1 x 2 backplane, perform the following steps: 1. In the customer kit, locate the nonterminated 68-pin SCSI cable. (This cable has two connectors at one end and one connector on the other end. See Figure 3.) )LJXUH,QVWDOOLQJWKH6&6,&DEOHWR[%DFNSODQH top drive connector bottom drive connector SCSI cable SCSI controller on system board 2. On the end with two connectors. a. Attach the connector at the end of the cable to the bottom drive connector. on the 1 x 2 backplane. b. Attach the second connector to the top drive connector on the 1 x 2. backplane. 3. Attach the end with one connector to a SCSI controller on the system board. &RQYHUWLQJWKH'ULYH&DUULHU. You can use only 1-inch hard-disk drives with the 1 x 2 backplane. If you have 1.6-inch. hard-disk drive carriers that you want to use with your 1 x 2 backplane, you need to. place 1-inch hard-disk drives in the carrier and modify the 1.6-inch carriers to be 1 inch. in width. To modify the 1.6-inch carriers to 1-inch width, remove the spacer insert. NOTE: To remove the spacer insert, use a screwdriver to pry open the clips on the. inside of the carrier release handle, and pull the spacer insert away from the carrier. After you have installed your 1 x 2 backplane, see .Installing and Removing SCSI. Hard-Disk Drives. in Chapter 10 of th. Installation and Troubleshooting Guid. for. information on how to install your hard-disk drives. NOTE: The 1 x 2 backplane sets the top drive to SCSI ID0 and the bottom drive to. SCSI ID1. . Dell PowerEdge 6300 and 4300 Systems 1 x 2 Backplane Installation Informatio. ...
Otros modelos de este manual:Computadoras - POWEREDGE 6300 (390.27 kb)