Votos - 1, Puntuación media: 5 ( )

Fabricar: Acer Tamaño del archivo: 658.63 kb Nombre del archivo: Idioma del manual:

• Don’t place the system in high traffic areas or where the power cord or other cords may be stepped on. • Avoid placing the system in any location that is excessively dusty or damp. Open package Open the package carefully and keep all packing materials for later use. Ensure that all items are present and in good condition. If any of the following items are missing or appear damaged, contact your dealer immediately. • Acer Power SP Series • PS2 keyboard • PS2 mouse • Spearkers ( for selected models only) • User’s Guide and Starter poster Other user documentation and third party software. 2.2. Connecting the peripherals Notice: Don’t connect system power cord before connecting all peripherals to the system. After everything is connected, plug the power cord into the system and insert the other end into a power outlet. 2.3. Starting your computer After connecting all the peripheral equipment, start your computer according to the below steps: 1. Power on all peripheral equipment, such as monitor, printer, fax, speakers etc. 2. Turn on the system. Once the start-up process is complete, you can begin to use the computer. Shutting down your computer From the “Start” Menu, select “Shut Down” and click OK. In the event of a system crash, press and hold the power button on the front of the system for four seconds. After the system has shut down, turn off all peripheral devices. 3. Upgrading your computer 3.1 Installation Precautions Reminder for guarding against static electricity Protect your system from power surges, read following section before installing any components. This section contains important ESD (Electrostatic discharge) precautions. ESD Guard ESD can damage the CPU, drives, expansion circuit boards and the other components. Before you install components, please observe the following precautions: 1. Do not remove new components from their protective packaging until you are ready to install them into the system. 2. Wear a wrist grounding strap and touch it to a metal part of the computer before installing the components. If a wrist grounding strap is not available, please maintain contact with the system case throughout any procedure requiring ESD protection. Pre-installation Instructions Always observe the following before you install any component: 1. Turn off your computer and any peripheral devices connected to it and unplug all cords from the system before you install any component into computer. 2. Open your computer system according to instruction setup manual. 3. Follow ESD precautions described above before handling any computer components. 4. Remove any expansion boards or peripherals that block to the DIMM sockets or component connectors. Warning! If the system is not properly shut down before you start to install components, your system may be damaged. Certain components of your computer are upgradeable such as the memory, the hard disk, the CPU and the expansion card. However, for safety purpose we do not recommend performing these upgrades yourself. If you want to replace or upgrade any of the components, contact your dealer or a qualified service technician. Post-installation Instructions After installing or upgrading any component: 1. Check whether all the components had been installed following the step by step instructions in their respective sections. 2. Replace any other components previously removed to allow access. 3. Replace the external panels. 4. Reconnect all peripheral cables and turn on the system power. 3.2 Opening your Computer This chapter introduces how to open the external panels when you need to install or upgrade components. Remove the side panel 1. Turn off your computer and unplug all peripheral devices. 2. Place the system on a flat, steady surface. 3. Remove the two screws on the side panel. 4. Slide the panel towards the back of the system and gently remove it. Replace the side panel 1. Put the cover back on the system. 2. Lock the panel with previously removed screws. 3.3. Replacing the HDD Upgrade the HDD 1. Remove all the HDD wires from the system’s mainboard. 2. Remove the 4 screws fixing HDD to the chassis. 3. Gently remove the HDD from the drive bay. 4. Reinstall the HDD: a. Insert the HDD into the bay b. Replace the 4 screws to secure the drive. 5. Connect the cables to the mainboard. 3.4. Installing PCI cards Install PCI card 1. Find an empty PCI slot on the motherboard. 2. Remove the screw holding the bracket to back panel and remove the bracket. 3. Take the new PCI card from its protective bag. 4. Position the PCI card in the slot and gently press to insert it. 5. Secure the card to your computer with the screw removed earlier. When you restart the system, BIOS (Basic Input/Output System) will automatically detect and allocate the resources to the new PCI device. Remove PCI card To remove PCI card, you only need to open the computer and remove the undesired card. 3.5. Installing additional memory Memory can be upgraded to a maximum of 2 GB. This can be ...

Descargar ahora

Introduzca dos números de la imagen: