Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
Memory modules are detected, but a memory failure has occurred. l If you have two or more memory modules installed, remove the modules, reinstall one module, and then restart the computer. If the computer starts normally, reinstall an additional module. Continue until you have identified a faulty module or reinstalled all modules without error. l If available, install properly working memory of the same type into your computer. l If the problem persists, contact Dell. A possible graphics card failure has occurred. l If the computer has a graphics card, remove the card, reinstall it, and then restart the computer. l If the problem still exists, install a graphics card that you know works and restart the computer. l If the problem persists, contact Dell. A possible floppy drive or hard drive failure has occurred. Reseat all power and data cables and restart the computer. A possible USB failure has occurred. Reinstall all USB devices, check cable connections, and then restart the computer. No memory modules are detected. l If you have two or more memory modules installed, remove the modules, reinstall one module, and then restart the computer. If the computer starts normally, reinstall an additional module. Continue until you have identified a faulty module or reinstalled all modules without error. l If available, install properly working memory of the same type into your computer. l If the problem persists, contact Dell. Memory modules are detected, but a memory configuration or compatibility error exists. l Ensure that no special memory module/memory connector placement requirements exist. l Verify that the memory modules that you are installing are compatible with your computer. l If the problem persists, contact Dell. A possible expansion card failure has occurred. 1. Determine if a conflict exists by removing a card (not a graphics card) and restarting the computer. 2. If the problem persists, reinstall the card that you removed, remove a different card, and then restart the computer. 3. Repeat this process for each card. If the computer starts normally, troubleshoot the last card removed from the computer for resource conflicts (see "System Setup Program"). 4. If the problem persists, contact Dell. Another failure has occurred. l Ensure that the cables are properly connected to the system board from the hard drive, CD drive, and DVD drive (see "System Board Components"). l If there is an error message on your screen identifying a problem with a device (such as the floppy drive or hard drive), check the device to make sure it is functioning properly. l The operating system is attempting to boot from a device (such as the floppy drive or hard drive); check the system setup program to make sure that the boot sequence is correct for the devices installed on your computer. l If the problem persists, contact Dell. The computer is in a normal operating condition after POST. None. Code Cause 1-3-1 through 2-4-4 Memory not being properly identified or used 4-3-1 Memory failure above address 0FFFFh System Messages Code Cause 1-1-2 Microprocessor register failure 1-1-3 NVRAM 1-1-4 ROM BIOS checksum failure 1-2-1 Programmable interval timer 1-2-2 DMA initialization failure 1-2-3 DMA page register read/write failure 3-1-1 Slave DMA register failure 3-1-2 Master DMA register failure 3-1-3 Master interrupt mask register failure 3-1-4 Slave interrupt mask register failure 3-2-2 Interrupt vector loading failure 3-2-4 Keyboard Controller Test failure 3-3-1 NVRAM power loss 3-3-2 NVRAM configuration 3-3-4 Video Memory Test failure 3-4-1 Screen initialization failure 3-4-2 Screen retrace failure 3-4-3 Search for video ROM failure 4-2-1 No time tick 4-2-2 Shutdown failure 4-2-3 Gate A20 failure 4-2-4 Unexpected interrupt in protected mode 4-3-3 Timer-chip counter 2 failure 4-3-4 Time-of-day clock stopped 4-4-1 Serial or parallel port test failure 4-4-4 Cache test failure NOTE: If the message you received is not listed in the table, see the documentation for either the operating system or the program that was running when the message appeared. Message Possible Cause Corrective Action 8042 Gate-A20 error The keyboard controller failed its test. If you receive this message after you make changes in the system setup program, enter the system setup program and restore the original value (s). Address Line Short! An error in the address decoding circuitry in the memory has occurred. Reseat the memory modules. C: Drive Error C: Drive Failure The hard drive is not working or is not configured correctly. Ensure that the drive is installed correctly in the computer and defined correctly in the system setup program. Cache Memory Bad, Do Not Enable Cache The cache memory is not operating. See "Contacting Dell" in your Owner's Manual for instructions on obtaining technical assistance. CH-2 Timer Error An error is occurring on the timer on the system board. See "Contacting Dell" in your Owner's Manual for instructions on obtaining technica...