Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
CAUTION The board is designed to be passively cooled on a properly ventilated chassis. Chassis venting locations are recommended over the processor, voltage regulator, and system memory areas for maximum heat dissipation effectiveness. Ensure that proper airflow is maintained around the processor, processor voltage regulator circuit, and the DIMM. Failure to do so may result in damage to these components. CAUTION A thermal rating of 85 oC is required for the DIMMs used on this board. Installing and Replacing Desktop Board Components Installation Precautions When you install and test the Intel Desktop Board, observe all warnings and cautions in the installation instructions. To avoid injury, be careful of: • Sharp pins on connectors or headers • Sharp pins on printed circuit assemblies • Rough edges and sharp corners on the chassis • Hot components (such as voltage regulators and heat sinks) • Damage to wires that could cause a short circuit Observe all warnings and cautions that instruct you to refer computer servicing to qualified technical personnel. Prevent Power Supply Overload Do not overload the power supply output. To avoid overloading the power supply, make sure that the calculated total current loads of all the modules within the computer is less than the output current rating of the power supply. Observe Safety and Regulatory Requirements Read and adhere to the instructions in this section and the instructions supplied with the chassis and associated modules. If you do not follow these instructions and the instructions provided by chassis and module suppliers, you increase safety risk and the possibility of noncompliance with regional laws and regulations. Refer to Appendix B for safety and regulatory requirements. Intel Desktop Board D2700MUD Product Guide Installing the I/O Shield The Desktop Board comes with an I/O shield. When installed in the chassis, the shield blocks radio frequency transmissions, protects internal components from dust and foreign objects, and promotes correct airflow within the chassis. Install the I/O shield before installing the Desktop Board in the chassis. Place the shield inside the chassis as shown in Figure 6. Press the shield into place so that it fits tightly and securely. If the shield does not fit, obtain a properly-sized shield from the chassis supplier. Figure 6. Installing the I/O Shield Installing and Replacing Desktop Board Components Installing and Removing the Desktop Board CAUTION Only qualified technical personnel should do this procedure. Disconnect the computer from its power source before performing the procedures described here. Failure to disconnect the power before you open the computer can result in personal injury or equipment damage. Refer to your chassis manual for instructions on installing and removing the Desktop Board. Figure 7 shows the location of the mounting screw holes for Intel Desktop Board D2700MUD. Figure 7. Intel Desktop Board D2700MUD Mounting Screw Holes Intel Desktop Board D2700MUD Product Guide Installing and Removing Memory NOTE To be fully compliant with all applicable Intel SDRAM memory specifications, the boards require SO-DIMMs that support the Serial Presence Detect (SPD) data structure. The Desktop Board has two 204-pin DDR3 SO-DIMM sockets that support up to 4 GB of system memory. To install system memory on the Desktop Board, see Figure 8 and follow these steps: 1. Observe the precautions in "Before You Begin" on page 25. 2. Install the first SO-DIMM (Figure 8, A) in the bottom (SO-DIMM 1) socket. Align the notch in the SO-DIMM with the key in the socket (Figure 8, B), while holding the SO-DIMM with the back edge tilted slightly upwards, insert it in the socket, and gently push the back edge down until it snaps into the retention arms (Figure 8, C). 3. If you are installing a second SO-DIMM, repeat Step 2 using the top (SO-DIMM 0) socket (Figure 8, D). Figure 8. Installing System Memory To remove an SO-DIMM from a socket, gently spread the socket’s retention arms (Figure 8, C) to disengage them from the SO-DIMM. Installing and Replacing Desktop Board Components Connecting SATA Drives The board has two SATA connectors each supporting one SATA drive. The included SATA cables support the Serial ATA protocol. For correct cable and drive function: 1. Observe the precautions in "Before You Begin" on page 25. 2. Attach one end of the cable to the connector on the board (Figure 9, A) and connect the other end to the drive (Figure 9, B). Figure 9. Connecting the Serial ATA Cable Intel Desktop Board D2700MUD Product Guide Installing a PCI Express Mini Card You can install a PCI Express Full-Mini Card or a PCI Express Half-Mini Card in the Desktop Board’s PCI Express Mini Card slot. To install a Full-Mini Card, see Figure 10 and follow these steps: 1. Observe the precautions in "Before You Begin" on page 25. 2. Insert the card into the PCI Express Mini Card connector (Figure 10, A) at a slightly upward angle. 3. Align the card’...