Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
2 Use the arrow buttons on the remote to highlight Devices in the menu and press OK on the remote. 3 If more than one device is displayed, use the arrow buttons on the remote to select one and press OK to view its files and folders. 4 Press the Menu key again to display the Devices menu. Use this menu to decide how to display the media on this device (Thumbnails or List) and which kinds of media files to display (Movies, Pictures, Music, or All). 5 When you have found the video, music or pictures you want to play, press Play on the remote. Note: Using the Devices menu is the only way to browse through the folders on a device and view media files within their folders. You can access the Devices menu either by selecting Devices from the menu or by selecting Browse Folders on the Video, Pictures or Music menus. English EnglishEnglish 28 Copy, move and delete When you are browsing for files in the Device screen, you can select files to copy, move and delete. Press Menu on the remote to bring up a sub-menu. Select Copy Files from the sub-menu and press OK. Select up to 8 files you would like to copy by pressing OK. 29 Press Menu on the remote and select Select Destination. When the destination is selected, press Menu to Paste. Note: It is recommended to use a PC to transfer files over 1 GB. Paste Adding a hard disk drive You may install a HDD if one is not already installed. English EnglishEnglish 30 1 Open the HDD door of the Aspire RevoView. 2 Remove the HDD carrier by pressing the HDD carrier latch. 3 Pull the lever and slide the HDD carrier out of the chassis. Insert the new drive into the right side of the carrier aligning the pins with the HDD mounting holes. Gently open out the left rail and insert the pins into the HDD mounting holes. English EnglishEnglish 32 6 With the lever still extended, slide the carrier all the way into the drive bay. Do not push on the lever until it begins to close by itself. 7 Use the lever to push the carrier until it is properly seated, then close the lever. Note: If the HDD is not already formatted, you can connect your Aspire RevoView to a computer using the USB cable and format the disk. Warning: Make sure the Aspire RevoView is disconnected from a power source while you are installing the HDD. If the Aspire RevoView is powered, you risk personal injury, data loss or damage to the Aspire RevoView and its components. Formatting a new HDD Insert the new HDD as described above. Connect your Aspire RevoView to a PC using the USB cable and to the AC adapter as described in “Using a direct connection” on page 5 and “Connecting the power cable” on page 7. 33 Open your computer’s Control Panel and open System and Security > Administrative Tools > Computer Management. English EnglishEnglish 34 Select Disk Management to enter initialize disk mode. Right-click the new disk and select New Simple Volume. Once complete, you will be able to see the new HDD. Adding a hard disk drive from an Acer Aspire easyStore Home Server You may install the Server Backup HDD from an Acer Aspire easyStore Home Server and use it with the Aspire RevoView. Safely remove the Server Backup HDD from your Acer Aspire easyStore Home Server. 2 Pull out the HDD from your home server. 3 Insert the HDD along with its HDD tray inside the Aspire RevoView. You can play the media content now. Adjusting settings The Aspire RevoView is ready for use as soon as you plug it in. However, you can adjust the system, audio, video, network and firmware upgrade settings for optimal use with your TV. English EnglishEnglish 36 Choosing a menu language The first time you connect your Aspire RevoView to your TV, a language selection screen asks you to select your menu language from a list of available languages. You can change your language selection at any time by going to System Setup > Menu Language. Configuring the Aspire RevoView Use the Settings menu to configure the system, audio, video, network, and firmware settings for your Aspire RevoView. 1 Press the arrow buttons on the remote to select Settings from the main menu, then press OK on the remote. 2 Select the feature you want to adjust the settings for and press OK on the remote. 3 To close the Settings menu, press Menu. Once you have opened one of the Settings screens, you can navigate through them using the left and right arrow buttons on the remote. System setup Menu Language: Select the language to be used in all media player menus. Text Encoding: Select the language to be used for media information. Time: Manually set the date and time. Version Information: View the software version currently installed on your Aspire RevoView. MAC Address: View the network ID assigned to the media player. IP Address: Set your Network IP or Wireless IP. Factory Default: Reset all setup menu functions to the factory defaults and display the initial language selection screen. Screen saver: Set how long the system idles before starting the screen saver. Play To support for Windows 7 Play ...