Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
FIGURE 1 SPARC Enterprise T5120 Server Shipping Contents Quantity Item 1 Server 2 RJ-45 Ethernet cable 1 RJ-45 to DB-25 adapter (crossover) 1 RJ-45 to DB-9 adapter (crossover) 1 Wrist strap 2 Power cords (packaged separately) 1 Rackmounting kit with cable management assembly Before You Begin For quick installation and configuration, follow these steps. For more detailed information, refer to the complete online product documentation set at: Understand the following information before you set up the server for the first time: ¦ Do not apply power until instructed to do so – This system includes a service processor (SP) that is used to configure and boot the host server. To properly configure the host server and view SP messages, do not apply AC power to the server until the SP and host networking connections are made, as described in this guide. ¦ Choose the best instructions for your situation – The quick setup instructions in this guide work for any networking environment, and require the use of a terminal device for connection to a serial port. If you have a networking environment running DHCP, you can configure your system using the Ethernet management port. To take advantage of the DHCP setup method, refer to the online installation guide in the online product documentation set at: ¦ ¦ ¦ Obtain a terminal device – You configure this rackmountable server through the SP using the built-in serial and network management ports, and not through a graphical interface and keyboard. To communicate with the SP, you will need a terminal device, which can be a terminal, terminal server, or laptop running terminal emulation software. ¦ Gather your configuration information – During the configuration, you are prompted for time zone and networking parameters for your environment. Use TABLE 1 to record your configuration information. TABLE 1 Configuration Information Parameter Description Your Entry Language Select a number from the displayed language list. Locale Select a number from the displayed locale list. Terminal Type Select a terminal type that corresponds with your terminal device. Network? Select Yes. Multiple Network Interfaces Select the network interfaces that you plan to configure. If you are not sure, select the first one in the list. DHCP? Select Yes or No according to your network environment. Host Name Enter the host name for the server. IP Address Enter the IP address for the selected Ethernet interfaces. Subnet? Select Yes or No according to your network environment. Subnet Netmask (If subnet was Yes) Enter the netmask for the subnet for your network environment. IPv6? Specify whether or not to use IPv6. If you are not sure, select No to configure the Ethernet interface for IPv4. Security Policy Select either standard UNIX security (No) or Kerberos Security (Yes). If you are not sure, select No. Confirm Review the onscreen information and change it if needed. Otherwise, continue. Name Service Select the name service according to your network environment. Note – If you select a name service other than None, you will be prompted for additional name service configuration information. NFSv4 Domain Name Select the type of domain name configuration according to your environment. If you are not sure, select Use the NFSv4 domain derived by the system. Time Zone (Continent) Select your continent. Time Zone (Country or Region) Select your country or region. Time Zone Select the time zone. Date and Time Accept the default date and time, or change the values. root Password Enter the root password twice. This password is for the superuser account for the Solaris OS on this server. This password is not the SP password. Quick Setup Instructions 1. Unpack the server, and check that you received all of the shipping contents (FIGURE 1). 2. Place the server in its intended location for verification. For rackmounting instructions, refer to the instructions included with the rail kit, the service label on the server, and to the online SPARC Enterprise T5120 and T5220 Servers Installation Guide. 3. Connect a serial cable between the server’s SER MGT port (FIGURE 2) and a terminal device. This connection provides your initial communication with the SP. The device must be set up to communicate using 9600 baud, 8 bit, no parity, 1 stop bit. A null modem configuration is needed, meaning the transmit and receive signals are reversed (crossed over) for DTE to DTE communications. You can use the supplied RJ-45 crossover adapters with a standard RJ-45 cable to achieve the null modem configuration. FIGURE 2 Server Connections 4. (Optional) Connect an Ethernet cable...
Otros modelos de este manual:Computadoras - SPARC T5120 (2.71 mb)