Votos - , Puntuación media: ( )

Manual de usuario Dell, modelo T5440

Fabricar: Dell
Tamaño del archivo: 11.31 mb
Nombre del archivo: t5440-service-en-03.pdf

Idioma del manual:

El documento se está cargando, por favor, espere

Descargar ahoraCerca

El documento se está cargando, por favor, espere

Descargar ahoraCerca

Switch to the system console and issue the Solaris OS fmadm faulty command. # fmadm faulty No memory faults should be displayed. If faults are reported, refer to the diagnostics flowchart in FIGURE: Diagnostic Flowchart on page 14 for an approach to diagnose the fault. 4. Switch to the ILOM command shell. 5. Run the show faulty command. ¦ If the fault was detected by the host and the fault information persists, the output will be similar to the following example: -> show faulty Target | Property | Value --------------------+------------------------+------------------------------/ SP/faultmgmt/0 | fru | /SYS/MB/CPU0/CMP0/BR0/CH1/D0 /SP/faultmgmt/0 | timestamp | Dec 14 22:43:59 /SP/faultmgmt/0/ | sunw-msg-id | SUN4V-8000-DX faults/0 | | /SP/faultmgmt/0/ | uuid | 3aa7c854-9667-e176-efe5-e487e520 faults/0 | | 7a8a /SP/faultmgmt/0/ | timestamp | Dec 14 22:43:59 faults/0 | | ¦ If the show faulty command does not report a fault with a UUID, then you do not need to proceed with the following step because the fault is cleared. 6. Run the set command. -> set /SYS/MB/CPU0/CMP0/BR0/CH1/D0 clear_fault_action=True Are you sure you want to clear /SYS/MB/CPU0/CMP0/BR0/CH1/D0 (y/n)? y Set ’clear_fault_action’ to ’true 112 SPARC Enterprise T5440 Server Service Manual • June 2011 Ў Ў If you are upgrading the system with additional FB-DIMMs, use this procedure. Before you begin, complete these tasks: ¦ Read the section, “Safety Information” on page 63. ¦ Read the sections, “FB-DIMM Configuration” on page 113 and “FB-DIMM Device Identifiers” on page 116. ¦ Power off the server using one of the methods described in the section, “Powering Off the System” on page 67. ¦ “Extend the Server to the Maintenance Position” on page 70 ¦ “Perform Electrostatic Discharge – Antistatic Prevention Measures” on page 73 ¦ “Remove the Top Cover” on page 73 ¦ “Remove a CMP/Memory Module” on page 104 1. Unpackage the FB-DIMMs and place them on an antistatic mat. 2. Ensure that the ejector tabs are in the open position. 3. Line up the FB-DIMM with the connector. Align the FB-DIMM notch with the key in the connector. This ensures that the FB-DIMM is oriented correctly. 4. Push the FB-DIMM into the connector until the ejector tabs lock the FB-DIMM in place. If the FB-DIMM does not easily seat into the connector, verify that the orientation of the FB-DIMM is correct. If the orientation is reversed, damage to the FB-DIMM might occur. 5. Repeat Step 2 through Step 4 until all the FB-DIMMs are installed. Next Steps ¦ “Install a CMP/Memory Module” on page 105 ¦ “Install the Top Cover” on page 154 ¦ “Slide the Server Into the Rack” on page 155 ¦ “Power On the Server” on page 157 FB-DIMM Configuration This topic includes the following: ¦ “Supported FB-DIMM Configurations” on page 114 Servicing Customer-Replaceable Units 113 ¦ ¦ Supported FB-DIMM Configurations Use these FB-DIMM configuration rules to help you plan the memory configuration of your server: ¦ Up to 16 FB-DIMMs can be installed in each CMP/memory module pair. ¦ Each bank consists of four FB-DIMMs. ¦ Each bank must be populated completely, never partially. ¦ For each CPU/Memory module pair, all FB-DIMMs must be of the same capacity, either 2 GB, 4 GB or 8 GB per FB-DIMM. ¦ Memory bank 0 must always be populated. ¦ Memory bank 1 must be populated before banks 2 and 3. ¦ Memory banks 2 and 3 must be populated simultaneously and completely. ¦ The number of FB-DIMMs installed on a processor and its associated memory expansion module must be either 4, 8 or 16. No other combinations are supported. ¦ 4 GB FB-DIMMs at 800 Mhz are available for 1.6-Ghz systems only and cannot be mixed with other FB-DIMMs of different speed within the same system. Memory Bank Configurations The following table describes the supported memory configurations, and the order in which FB-DIMMs must be added. Banks 2 and 3 must be either Bank 1, if filled, must contain completely empty or completely filled. FB-DIMMs of the same capacity as If filled, they must have the FB-DIMMs Bank 0 of the same capacity as Banks 0 and 1 CPU Module (Includes Memory Bank 0) Memory Module (Includes Memory Banks 1, 2 and 3.) Configuration Number Memory Bank 0 Memory Bank 1 Memory Bank 2 Memory Bank 3 Total Memory Configuration 1 4 x 2 Gbyte – – – 8 GBytes Configuration 2 4 x 2 GByte 4 x 2 GByte – – 16 GBytes Configuration 3 4 x 2 GByte 4 x 2 GByte 4 x 2 GByte 4 x 2 GByte 32 GBytes Configuration 4 4 x 4 GByte – – – 16 GBytes Configuration 5 4 x 4 GByte 4 x 4 GByte – – 32 GBytes 114 SPARC Enterprise T5440 Server Service Manual • June 2011 Banks 2 and 3 must be either Bank 1, if filled, must contain completely empty or completely filled. FB-DIMMs of the same capacity as If filled, they must have the FB-DIMMs Bank 0 of the same capacity as Banks 0 and 1 Banks 2 and 3 must be either Bank 1, if filled, must contain completely empty or completely filled. FB-DIMMs of the same capacity as If filled, they must have the FB-DIMMs Bank 0 of the same capacity as...