Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Computadoras - HP 1155 All-in-One Desktop series (389.51 kb)
Computadoras - HP 1155 All-in-One Desktop series (382.48 kb)
Resumen del manual
Advanced Bus Options - Allows you to enable/disable PCI SERR# Generation and
Password Security and CMOS
(continued) PCI VGA palette snooping.
Onboard Devices - Allows you to set resources for or disable on-board
Establishing a Setup or Power-On password
system devices.
1. Turn on or restart the computer.
Device Options - Al ows you to set:
2. As soon as the computer turns on, press the Esc key while “Press the ESC key for
• Printer mode (Bi-Directional, EPP + ECP, Output Only)
Startup Menu” message is displayed at the bottom of the screen.
• Num Lock State at Power-on (off/on)
3. Press the
• Integrated Video (enable/disable)
F10 key to enter Computer Setup.
• Integrated Graphics (Auto/Disable/Force)
4. To establish Setup password, select Security > Setup Password and follow the
• Internal Speaker (enable/disable)
instructions.
• NIC PXE Option ROM Download (enable/disable)
- or -
• SATA RAID Option ROM Download (enable/disable)
To establish a Power-On password, select Security > Power-On Password and
• Multi-Processor (enable/disable)
follow the instructions on the screen
• Hyper-threading (enable/disable)
5. Before exiting, click File > Save Changes and Exit.
• Turbo Mode (enable/disable)
VGA Configuration - Allows you to specify which VGA controller is the
“boot”/primary. Displayed only if add-in video card installed.
AMT Configuration - Allows you to set:
Resetting a Setup or Power-On password
• AMT (enable/disable)
1. Turn off the computer and disconnect the power cord from the power outlet.
• Unconfigure AMT/ME (enable/disable)
• Hide Unconfigure ME Confirmation Prompt (enable/disable)
2. Remove the access panel.
• Watchdog Timer (enable/disable)
3. On the system board, locate the header labeled CLR PASSWORD.
4. Remove the jumper and place it on pins 1 and 2.
5. Wait for three seconds, and then replace the jumper to its original position (pins 2
Common POST Error Messages
and 3).
6. Replace the access panel and reconnect the power cord.
Screen
Message
Probable Cause
Recommended Action
7. Turn on the computer and al ow it to start.
101-Option ROM
System ROM or expansion
1. Verify ROM, reflash if required
Error
board option ROM check-
2. Remove recently added cards to see if
sum.
problem remains.
Resetting CMOS
3. Clear CMOS. If message disappears, may
be card problem.
1. Turn off the computer and disconnect the power cord from the power outlet.
4. Replace system board
2. Remove the access panel.
103-System Board DMA or timers
1. Clear CMOS memory.
3. On the system board, locate the header labeled CLR CMOS.
Failure
2. Remove expansion boards.
3. Replace system board.
4. Remove the jumper and place it on pins 2 and 3.
163-Time & Date
Invalid time or date in con-
Reset the date and time under Control Panel
5. Wait for three seconds, and then replace the jumper to its original position (pins 1
Not Set
figuration memory.
(Computer Setup can also be used). If the
and 2).
RTC battery may need to be problem persists, replace the RTC battery.
replaced.
6. Replace the access panel and reconnect the power cord.
164-Memory Size
Memory amount has
Press the F1 key to save the memory changes.
7. Turn on the computer and al ow it to start.
Error
changed since the last boot
(memory added/removed).
164-Memory Size
Incorrect memory configura- 1. Run Setup (F10).
Error
tion
2. Make sure memory module(s) installed
properly.
3. If third-party memory added, test using HP-
only memory.
1. Verify proper module type.
201-Memory Size
RSM failure
1. Ensure memory modules are correctly
Error
installed.
2. Verify proper module type.
3. Remove and replace faulty module(s).
4. If error persists after replacing modules,
replace system board.
214-DIMM Config- Populated DIMM configura-
Rearrange DIMMs so that each channel has
uration Warning
tion is not optimized
the same amount of memory.
219-ECC Memory Recently added memory
1. If additional memory was recently added,
Module Detected
module(s) support ECC
remove it to see if the problem remains.
ECC Modules not
memory error correction.
2. Check product documentation for memory
supported on this
support information.
Platform
301-, 304-Key-
Keyboard failure.
1. Reconnect keyboard with system turned off.
board error
2. Check kybd connection or keys.
3. Check connector for bent or missing pins.
4. Replace keyboard.
5. If 304, possible sys bd problem.
511-CPU Fan not
CPU Fan not Detected.
1. Reseat CPU fan.
Detected
2. Reseat fan cable.
3. Replace CPU fan.
1805-Ambient
This system was placed in a Make sure the system meets the HP enclosure
Temperature Pre-
low power state to prevent
guidelines as listed in the Quick Specs, includ-
viously Over Limit
damage due to excessive
ing the following:
environmental temperature.
1. Clean the air vents on the front, back, or any
other vented side of the computer.
2. Ensure that there is a 10.2 cm (4 in)
clearance on all vented sides of the
computer to permit the required airflow.
3. Ensure that computers are not so near each
other that they are subject to each other's
re-circulated or preheated air.
2200-PMM Alloca- (2200) Memory error during 1. Reboot the computer.
tion Error during
POST execution of the Man- 2. Unplug the power cord, re-seat the memory
MEBx Download
agement Engine (ME) BIOS
modules, and reboot the computer.
Extensions option ROM.
2201-MEBx Mod-
3. If the memory configuration was recently
ule did not check-
(2201) Memory error during
changed, unplug the computer, restore the
sum correctly
POST execution of the Man-
original memory configuration, and reboot
agement Engine (ME) BIOS
the computer.
2202-PMM Deallo- Extensions option ROM.
4. If the error persists, replace the system
cation Error during
board.
MEBx cleanup
(2202) Memory error during
POST execution of the Man-
agement Engine (ME) BIOS
Extensions option ROM.
2230-General
(2230) Error occurred during 1. Reboot the computer.
error during MEBx MEBx execution which fails
execution
into the “General” grouping. 2. If the error persists, update to the latest
Status information displayed
BIOS version and ME firmware version.
2231-ME error dur- along with the error provides 3. If the error still persists, replace the system
ing MEBx execu-
further clarity into the failure.
board.
tion
MEBx handles transference
of information between the
2232-AMT error
system BIOS and ME firm-
during MEBx exe-
ware.
cution
(2231) Error occurred during
2233-HECI error
MEBx execution which fails
during MEBx exe-
into “ME” grouping.
cution
(2232) Error occurred during
MEBx execution which fails
into “AMT” grouping.
(2233) Error occurred during
MEBx execution which fails
into “MEI or HECI” grouping.
HP 1155 All-in-One Business PC
730784-001
page 3