Iniciar sesión:
Votos - , Puntuación media: ( )

Manual de usuario HP, modelo HP ProLiant XL220a Gen8 v2 Server

Fabricar: HP
Tamaño del archivo: 709.45 kb
Nombre del archivo:

Idioma del manual:en

El documento se está cargando, por favor, espere
El documento se está cargando, por favor, espere


Otros manuales para este modelo:

Resumen del manual













Anti-tip stabilizer
Rack rail instal ation depends on your rack configuration. Be sure to
follow the appropriate markings on the rack rails and select the correct
HP Apol o 6000 Power Shelf
Overview
The anti-tip stabilizers provide stability and support when equipment is
image for your setup.
Rack Rail in HP Racks
This document provides instructions for instal ing the HP Apollo 6000
instal ed, removed or accessed within the rack. Stabilizer kits are
Power Shelf Rack Rail kit.
available in both 600-mm and 800-mm versions. HP also recommends

using the side feet, provided with these kits, to stabilize stand-alone
Installation Instructions
Hardware kit contents
racks from the other side. If you are stabilizing racks that are secured
together with baying kits, the side feet are optional on either end of the



row.

HP recommends that stabilizer option kits be used when one or more of
the following situations occur:

The standard 600-mm (23.62-in) or 800-mm (31.50-in) front foot
is required with deployments of stand-alone racks.

Side feet, which are included in the stabilizer kits, are
recommended to be instal ed as well.
Rack rows with four or more bayed racks, without a single
rack-mountable component exceeding 99.79 kg (220 lb), do not need

a stabilizer kit installed.



Important safety information
See the Important Safety Information document included with the

server.


Item
Hardware (Scale: 1:1)
Quantity/Tool
CAUTION: Electrostatic discharge (ESD) can damage
electronic components. Be sure that you are properly
A
6 Alignment pins T-15
grounded (earthed) before beginning any instal ation

Torx
procedure.
B
4 10-32 Panhead


shoulder screws T-25


Torx
Installing the product in a rack
C
2 10-32 Flathead screws

T-15 Torx
The following procedure has steps that contain two images. Each

image illustrates a rack unit alignment method for installing the rack
D
4 10-32 Slot ed screws
rails:
T-25 Torx

The top image illustrates a full U rack unit installation.



The bottom image illustrates a 1/2 U rack unit installation.
Extra hardware might be included for your convenience.

Instal ation information
This hardware kit only supports HP Standard square-hole racks.

Rack warnings

WARNING: To reduce the risk of personal injury or
damage to the equipment, be sure that:
© Copyright 2014 Hewlet -Packard Development Company, L.P.
• The leveling jacks are extended to the floor.
The information contained herein is subject to change without notice. The only
• The ful weight of the rack rests on the leveling jacks.
warranties for HP products and services are set forth in the express warranty
• The stabilizing feet are attached to the rack if it is a
statements accompanying such products and services. Nothing herein should
single-rack installation.
be construed as constituting an additional warranty. HP shall not be liable for

technical or editorial errors or omissions contained herein.
The racks are coupled together in multiple-rack
installations.
• Only one component is extended at a time. A rack may
become unstable if more than one component is
Part Number: 752053-001
extended for any reason.
*752053-001*

May 2014

Edition: 1
752053-001
WARNING: If you are going to use a lift, be sure to use a
lift that can handle the load of the component.



...

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría