Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
Or you may need to install the optional components into the system. This section tells how to remove/install the following components: 1. System fans 2. ASUS PIKE RAID card (optional) 3. ASUS ASMB4-iKVM (optional) Ensure that the system is turned off before removing any components. 2.8.1 System fans To uninstall the system fans: 1. Disconnect the system fan cablefrom the fan connector on the motherboard. 2. Lift the fan, then set aside. 3. Repeat steps 1 to 2 to uninstall the other system fans. To reinstall the system fans 1. Insert the fan to the fan cage. The airflow directional arrow on the fan side should point towards thesystem rear panel. 2. Connect the system fan cable to the fan connector on the motherboard. ASUS RS500A-E6/PS4 2.8.2 Installing ASUS PIKE RAID card (optional) Follow the steps below to install an optional ASUS RAID card on your motherboard. If you install the PIKE 1078 or PIKE 2008 Series SAS RAID card, follow steps 1 and 2 to remove the outer heatsink on RAID card. 1. Remove the two screws that secure the heatsink bracket on the back of the SAS RAID card. Heatsink bracket 2. Remove the two screws that secure the outer heatsink on the front of the SAS RAID card. DO NOT remove the inner heatsink from the SAS RAID card. 3. Locate the PIKE RAID card slot on the motherboard. 4. Align the golden fingers of the RAID card with the PIKE RAID card slot. Chapter 2: Hardware setup 5. Insert the RAID card into the PIKE RAID card slot. Ensure that it is completely seated on the PIKERAID card slot. 6. Remove the data cables connected to the SATA connectors on the motherboard. 7. Connect the data cables, bynumerial order, to the SAS connectors labeled SAS1-4 (red) on the motherboard. 8. Remove the SGPIO cable from the SGPIO3 connector on the motherboard. ASUS RS500A-E6/PS4 9. Connect the SGPIO cable to the SGPIO1 connector on the motherboard. 10. Set the SGPIO_SEL1 jumper onthe backplane to pin 2-3 whenconnecting data cables to the SASconnectors on the motherboard. The heatsink on PIKE 1078/PIKE 2008 Series might interfere the components on the expansion card. Ensure that the height of the components is less than 5.8 mm. Chapter 2: Hardware setup Installing i Button (for PIKE 1078 only) Follow the steps below to install an optional i Button on your motherboard. 1. Locate the I Button slot on the motherboard. 2. Snap the I Button in place. ASUS RS500A-E6/PS4 2.8.3 Installing ASMB4 series management board (optional) Follow the steps below to install an optional ASMB4 series management board on your motherboard. 1. Locate the BMC_FW header on the motherboard. 2. Orient and press the ASMB4 management card in place. 3. Insert the LAN cable plug tothe LAN port 3 (dedicatedLAN) or LAN port 1 (sharedLAN) for server management. LAN port 3 LAN port 1 Chapter 2: Hardware setup Chapter 3 This chapter describes how to installthe optional components and devicesinto the barebone server. 2Installation options ASUS RS500A-E6/PS4 3.1 Installing friction rail kit items Your friction rail kit package contains: • Two pairs of rack rails (for the rack) • Nut-and-bolt type screws and one pair of server latches Nuts and screws Front rack rails Rear rack rails 3.1.1 Attaching the fixing latches to the server Refer to the image below for the locations to attach the two fixing latches to the two sides of the server with four screws. Fixing latch Chapter 3: Installation options 3.1.2 Attaching the rack rails To attach the rack rails 1. Place the two front rail rack joints into the rear rail rack slots, as shown in the following figure. 2. Attach the front and rear rail racks with eight screws and nuts, as shown in the following figure. Do not secure the screws too tight so that you can still adjust the length of the rack rails to meet the depth of the server rack. Front rail rackRear rail rack FrontrailrackjointsRear rail rack slots 3.Select one unit of space (1U) on the rack where you want to install the barebone server. 4.Measure the depth of the rack to determine the length of the rack rails. 5.Adjust the rack rail to ensure that it fits the rack. 6.Position the rack rail to the 1U space on the rack. Ensure that the front end of the rack rail goes to the front of the rack space. 7. Secure the front end of the rail with two rack screws, as shown in theright figure. 8. Secure the rear end of the rail with two rack screws, as shown in theright figure. 9. Fasten the eight screw you securein step 2, as shown in the rightfigure. 10. Repeat steps 6 to 9 to assembleand attach the rack rail on the other side. 798 7 9 8 ASUS RS500A-E6/PS4 3.1.3 Mounting the server to the rack To mount the server to the rack 1. Place the server on the rack rails, and then push the server all the way to the depth of the rack. 2. Tighten the two rack screws to secure the server in place. To uninstall the server from the rack 1. Loosen the rack screws that secured the server to the rack. 2. Pull the server from the rack. Remember to press the latcheson bo...