Votos - 3, Puntuación media: 3.3
(
)
)
|
Resumen del manual
The stabilizer must be deployed every time a server is pulled out of the rack. Checking Components This section explains how to check the SPARC Enterprise M3000 server components. 1. Check the delivered items against the list of attachment that came with the server. Note — If any optional item, such as additional memory or a PCI Express (PCIe) card, is shipped separately, do not install it until normal operation of the server is confirmed. 3-1 3.2 3.3 3.3.1 2. Check for a model name and configuration on the product test record. If any of the items on the list of attachment or the product test record are missing, incorrect, or damaged, contact your sales representative. Mounting the Server in the Equipment Rack The SPARC Enterprise M3000 server is mounted in the equipment rack for use. For the mounting procedure, refer to the SPARC Enterprise Equipment Rack Mounting Guide. Caution — Do not grab the handle on the front of the server to lift the server. This handle should be used only to insert the server into or pull it out from the equipment rack (referred to as the rack). The handle is not designed to support the weight of the server. Connecting Cables This section explains how to connect power cables and the administration console. Connecting Power Cables This server is shipped with a grounded type (three-wire type) of power cable. Always connect the power cables into grounded power outlets. Caution — The server is designed to work with power systems having a grounded neutral conductor. Do not connect the equipment into any other type of power system. Contact the facilities manager or a qualified electrician to determine what type of power is supplied to your building. 3-2 SPARC Enterprise M3000 Server Installation Guide • January 2009 1. An electrician on site must confirm that the input power source satisfies the electrical power requirements. For the power requirements, refer to the SPARC Enterprise M3000 Server Site Planning Guide. 2. Make sure that each power cable is connected to the server and secured with an AC cable clamp. Do not connect the AC power supply system yet. 3. Arrange the layout of all cables outside the server, and secure them at the specified locations to prevent them from being damaged. 4. Make sure that the AC power source circuit breaker is in the OFF position, and then connect the power cables to the AC power supply system. For redundancy in case of a power source failure, PSU#0 and PSU#1 must be powered from separate sources. For the form of connection of the power cables, refer to Section 2.2.2.2, “Facility Power Requirements and Characteristics” on page 2-5. 3.3.2 Connecting a UPS An uninterruptible power supply (UPS) is used to provide a stable supply of power to the system in the event of a power failure or an extensive power interruption. A UPC port on the rear panel of the server can be connected to the UPC interface on the UPS so that emergency shutdown processing can be executed safely. If a UPS is procured, the UPS must have a separate power supply system. Connect PSU#0 and PSU#1 independently to the systems for AC power supply. (See FIGURE 3-1.) In a connection with 1+1 redundancy, a UPS cable is connected to the UPC 0 port on the server. In a dual power feed connection, UPS cables are connected to the UPC0 port and UPC1 port. Note — The UPC1 port cannot be used for a connection with 1+1 redundancy. For the UPC port interface specifications, refer to the SPARC Enterprise M3000 Server Service Manual. Chapter 3 Installing the Server 3-3 FIGURE 3-1 UPC Connections With a Dual-Power Feed Connection PSU#1 PSU#0 UPC1 UPS cable CB UPS#0 CB UPS#1 / CB: Circuit breaker AC#0 AC#1 3.3.3 Connecting the Administration Console The server is set up and statuses are displayed from the XSCF Shell through the serial port on the XSCF unit. To connect the administration console with the serial port, use the RS-232C cable (serial cable) supplied with the server. Also, the XSCF Shell and the domain console (OS console) can be used with a terminal connected to the serial port. Note — The XSCF board is secured on the motherboard unit (MBU) in the SPARC Enterprise M3000 server. In this document, the XSCF board in the SPARC Enterprise M3000 server is called the XSCF unit. You can use any of the following devices with a DB-9 serial port as the administration console: ■ ASCII terminal ■ Workstation ■ Terminal server (or a patch panel connected to a terminal server) ■ Personal computer 3-4 SPARC Enterprise M3000 Server Installation Guide • January 2009 Note - It is possible to connect it to a LAN port via telnet or SSH access. The LAN port has a Class B private address value, but it will not send out a packet by itself until configured. Note — The modular connector (RCI connector) is not for use with a TNV circuit connection. See Item 1 in FIGURE 3-2. 1. Confirm that the following settings have been made for software on the...
Otros modelos de este manual:Computadoras - M3000 M3000 (2.07 mb)