Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
Never connect, or disconnect cables during a thunderstorm. Never pull on a cable when disconnecting it. Always take hold of the cable by the plug. Follow the sequence described below to connect or disconnect external devices to or from the server: Be sure to wait for 10 seconds or more after shutdown before turning the server on. Connecting cables E Turn off all power and equipment switches. E Disconnect all power plugs from the properly grounded power outlets. E Connect all cables to the server and peripherals. E Plug all data communication cables into the utility sockets. E Plug all power cords into the properly grounded power outlets. Disconnecting cables E Turn off all power and equipment switches. E Disconnect all power plugs from the properly grounded power outlets. E Unplug all data communication cables from the utility sockets. E Disconnect the relevant cables from the server and all the peripherals. I For connecting or disconnecting LAN cables, the server need not to be powered off. To avoid loss of data teaming function has to be enabled. RX600 S5 Operating Manual Notes on connecting/disconnecting cables Hardware installation 62 Operating Manual RX600 S5 5 Starting up and operation V CAUTION! Follow the safety instructions in chapter "Important information" on page 27. 5.1 Control elements and indicators 5.1.1 Front of server ....1 ....4 #0#1 #2#5#4#3#6 #7 ..5 Figure 12: Front - overall view 1 ID card 5 Video connector 2 ServerView Local Service Display 6 3x USB connector 3 Optical drive activity indicator 7 Hard disk indicators 4 Control panel (for details see page 64) 8 Tape (optional) The white numbers in figure 12 show the HDD slot assignment. RX600 S5 Operating Manual Control elements and indicators Starting up and operation .................. Figure 13: Front - detailed view: control panel 1 ID indicator 6 Reset button 2 CSS indicator 7 NMI button 3 Global Error indicator 8 On/Off button 4 Hard disk activity indicator 9 ID button 5 Power-on indicator ID card You can pull out the ID card (see figure 12 above) as far as it will go and push it back in again. The ID card contains various system information, such as product name, serial number and order number; in the Japanese market only the product name and the serial number. 64 Operating Manual RX600 S5 Starting up and operation Control elements and indicators 5.1.1.1 Control elements ID ID button ID LED lights up (blue) on the front and on the rear of the server when the ID button is pressed. Both ID indicators are synchronized. On/Off button When the system is switched off, it can be switched on again by pressing the On/Off button. When the system is operating, pressing the On/Off button will switch off the system. V CAUTION! Risk of loss of data! I The On/Off button does not disconnect the server from the mains voltage. To disconnect from the mains completely, remove the power plug(s). RST Reset button Pressing the reset button reboots the system. V CAUTION! Risk of loss of data! NMI NMI button V CAUTION! Do not press! Risk of loss of data! The NMI button may only be used by service. RX600 S5 Operating Manual Control elements and indicators Starting up and operation 5.1.1.2 Indicators on the control panel ID ID indicator (blue) Lights up blue when the system has been selected by pressing the ID button. To deactivate, press the button again. The ID indicator can also be activated via the ServerView Operations Manager and the iRMC S2 Web interface and its status reported to the ServerView Operations Manager and the iRMC S2. Power-on indicator (green/orange/yellow) Lights up green – and also lights up orange for less than one second – when the server is switched ON. Flashes green when the system is in standby mode. Lights up orange when the server is in shutdown mode (operating system shutdown) or is switched off. Lights up yellow during power on delay. CSS CSS indicator (yellow) – Lights up yellow if a prefailure event was detected for a CSS component that you can fix yourself (for reasons of precaution) with the CSS concept. – Flashes yellow if an error was detected that you can fix yourself with the CSS concept. – Does not light up when the system is OK. If the event is still acute after a power failure, the indicator is activated after the restart. The indicator also lights up in standby mode. For more information on the CSS concept, see "Customer Self Service (CSS)" on page 14. Hard disk activity indicator (green) Lights up green when an internal hard disk drive is accessed. 66 Operating Manual RX600 S5 Starting up and operation Control elements and indicators ! Global Error indicator (orange) – Lights up orange if a prefailure event has been detected that requires (precautionary) service intervention. – Flashes orange if an error was detected that requires service intervention. – Does not light up if there is no critical event. If the event is still acute after a power failure, the indicator is activated after the restart. The indicator ...
Otros modelos de este manual:Computadoras - PRIMERGY RX600 S5 (2.42 mb)