¦ “Safety Information” on page 63 ¦ “Required Tools” on page 66 ¦ “Obtain the Chassis Serial Number” on page 66 ¦ “Obtain the Chassis Serial Number Remotely” on page 66 ¦ “Powering Off the System” on page 67 ¦ “Extending the Server to the Maintenance Position” on page 69 ¦ “Remove the Server From the Rack” on page 71 ¦ “Perform Electrostatic Discharge – Antistatic Prevention Measures” on page 73 ¦ “Remove the Top Cover” on page 73 Related Information ¦ “Managing Faults” on page 11 ¦ “Servicing C

875-4324-10 February 2008, Revision A Copyright 2008 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, U.S.A. All rights reserved. Copyright 2008 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, U.S.A. All rights reserved. Sun Microsystems, Inc. and Fujitsu Limited each own or control intellectual property rights relating to products and technology described in this document, and such products, technology and this document are protected by cop

Since the boot device always has a mounted file system when booted, an alternate boot medium must be employed, and the volume created in that environment. One alternate medium is a network installation image in single-user mode. (Refer to the Solaris 10 Installation Guide for information about configuring and using network-based installations.) 1. Determine which disk is the default boot device. From the OpenBoot ok prompt, type the printenv command, and if necessary the devalias command, to i

Please check for the recent update on your product. Fujitsu Welcomes Your Comments If you have any comments or requests regarding this document, or if you find any unclear statements in the document, please state your points specifically on the form at the following URL. For Users in U.S.A., Canada, and Mexico: (https://download.computers.us.fujitsu.com/) For Users in Other Countries: ( ml) x SPARC Enterprise T5120 and T5220 Servers Site Planning Guide • July 2009 SPARC Enterprise T5120

Please check for the recent update on your product. Fujitsu Welcomes Your Comments We would appreciate your comments and suggestions to improve this document. You can submit your comments by using "Reader's Comment Form"\ Reader's Comment Form FOLD AND TAPE FOLD AND TAPE BUSINESS REPLY MAIL FIRST-CLASS MAIL PERMIT NO 741 SUNNYVALE CA NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES POSTAGE WILL BE PAID BY ADDRESSEE FUJITSU COMPUTER SYSTEMS ATTENTION ENGINEERING OPS M/S 249 1250 EAST ARQUES AV

See “Run POST in Maximum Mode” on page 28. POST error messages use the following syntax: c :s > ERROR: TEST = failing-test c:s > H/W under test = FRU c:s> Repair Instructions: Replace items in order listed by H/W under test above c: s > MSG = test-error-message c:s > END_ERROR In this syntax, c = the core number, s = the strand number. Warning and informational messages use the following syntax: 42 SPARC Enterprise T5440 Server Service Manual • July 2009 INFO or WARNING: message In COD

1 1 ni 1 e Caution — The latch is not an ejector. Do not bend the latch too far to the right. Doing so can damage the latch 5. Grasp the latch and pull the drive out of the drive slot. Related Information ■ “Install a Hard Drive” on page 73 ■ “Four-Drive Capable Backplane Configuration Reference” on page 77 ■ “Eight-Drive Capable Backplane Configuration Reference” on page 78 ■ “Sixteen-Drive Capable Backplane Configuration Reference” on page 79 ▼ Install a Hard Drive Installing a hard

You can use the supplied RJ-45 crossover adapters with a standard RJ-45 cable to achieve the null modem configuration. FIGURE 2 Server Connections 4. (Optional) Connect an Ethernet cable between the server’s NET MGT port (FIGURE 2) and the network to which future connections to the SP and host will be made. After the initial configuration of the system using the SER MGT port, communication with the SP and host is usually performed through this Ethernet interface. 5. Connect an Ethernet cable bet