Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Убедитесь в том, что панель полностью закрыта. Внимание! Установку кондиционера рекомендуется производить силами квалифицированного персонала. С целью избежания сбоев в работе устанавливаемого кондиционера как результата его неквалифицированной установки обратитесь за помощью в сервисный центр; Все перемещения блоков кондиционера рекомендуется производить под руководством квалифицированного персонала. Кондиционер должен иметь правильно установленный 26 -е- ENGLISH 7. Please refer to the name plate for the performance indicator and the rated parameter. INSTALLATION MANUAL I. INSTALLATION PROCEDURE Read this manual before installation. You have to follow this manual during installation. The manufacturer reserves the right to make any changes to the machine or components of this model deemed necessary for technical and/or commercial reason without informing the public. However, you can contact their centre. Packing and accessories for indoor unit No. Description 1 Wall hanging panel 2 Operation manual 3 Remote controller 4 No. 7 dry battery 5 Screws for fixing wall hanging panel 6 Connection wire for Internal and external units 7 Sensor wire (only for heating pump type) 8 Plastic screw sleeve 9 Active carbon electrostatic filter 10 Low temperature catalyst Selection of Installation Place Indoor unit 1) Such a place from where cool air can be distributed throughout the room. 2) Place, where a distance marked is available as illustrated and the filter can be easily taken out. 3) Place where the distance of more than 1 m from television, videos, and fluorescent lamps. 4) Place not causing vibration, where the body can be supported sufficiently. Outdoor unit 1) Place, where is less affected by rain or direct sunlight and is sufficiently ventilated. 2) Place, where a distance marked is available as illustrated. 3) If the one-way refrigerant piping exceed 5 m, change the refrigerant additionally for 15g per 1 m (note: Pipes should be shorter than 7 m). 4) Check that the location of the unit is strong enough to support the weight of the unit, If not, reinforce the location with a board or beam, and then start the installation work. If the foundation is not strong enough, there may be excessive vibration and noise. 5) Place, where blow-out air and noises will not annoy the neighborhood. 6) Keep space necessary for installation service. Keep space from obstacles as shown in the right figure to prevent short circuit. (Keep 1 m or more for the upper space.) 7) It is not recommended to install in the environment of grease, very high humidity and corrosive gas. Indoor unit Outdoor unit 1) Checking the levels, fix a mounting plate on 1) Installing of outdoor unit, stud and cleat. 2) Connection of pipes. 2) Making hole in wall and fitting of piping. 3) Air ejecting & leak checking. 3) Cable connection. 4) Connection of inside and outside cable. 4) Installation of pipes. 5) Connection of drain pipe. 5) Installing the indoor unit Quantity 1 1 1 2 8 1 1 8 1 1 11 h conder.qxd 17.03.03 10:44 Page 24 ENGLISH II. INSTALLATION OF INDOOR AND OUTDOOR UNITS DIAGRAM How to open the front panel 1) Grasp the niches on each side of the bottom “A” of the front panel open the inlet grille by pulling upwards. 2) You have to follow this manual during installation. is - c How to close the front panel By pushing both sides “B” and the centre “C” as shown on the fig. Be sure that the front panel is completely closed. Handling the wireless remote controller. 1) When operating, point the signal sending head toward the signal receiver of the indoor unit. 2) A digital beeping sound will be heard when signal from the wireless remote controller is received. 3) The distance that signal can be received is not more 8m. III. INDOOR UNIT INSTALLATION A. Fix the mounting plate 1) Make sure once more the proper level of the plate, by hanging a thread with a weight from the top of the centre of the plate and mark the positions of the six screws. 2) Drill 6 holes of 6.4 mm & 30 mm depth holes for screw. 3) Using the provide plastic screw sleeve. 4) Fasten securely the plate with the provided self tapping screw. B. Making hole on the wall and fitting the piping hole sleeve 1) Position the wall hole as shown on the below diag. 2) Make a hole of 65 mm in diameter, slightly descending to outside the wall about 10-15 mm. Attention: In order to protect the wire through the wall, the provided piping hole sleeve should be used. C. Cable connection 1 ) The wire cable and the refrigerant pipe are winded together passing through the wall hole. 2) Open the grille & remove the wiring cover. 3) Connect the wire by using the plug & socket. After connection, fix the cable with the clamp without fail. D. Installation of pipes 1 ) Preparation work a) Draws pipes & drain hose at the back of the indoor unit. b) Fasten the refrigerant pipe & drain hose with the non-ad...
Otros modelos de este manual:Los acondicionadores de aire - VT-2108 (519.79 kb)
Los acondicionadores de aire - VT-2109 (519.79 kb)