Votos - 5, Puntuación media: 3.8
(
)
)
|
Resumen del manual
(Remember to open the vent during this function, but keep it closed during cooling for maximum cooling efficiency.) You can choose any fan speed you prefer. During this function, the display will show the actual room temperature, not the set temperature as in the cooling mode. YOU WILL SEE: LIGHT On 8 TO USE THE ENERGY SAVER FEATURE: DO THIS: PRESS ENERGY SAVER BUTTON Note: In this mode, the fan will continue to run for 3 minutes after the compressor shuts off. The fan then cycles on for 2 minutes at 10 minute intervals until the room temperature is above the set temperature, at which time the compressor turns back on and cooling stars. YOU WILL SEE: Air Conditioner Features (continued) LIGHT On TIMER: DELAY STOP / START FEATURE DO THIS: PRESS TIMER BUTTON YOU WILL SEE: TIMER SETTING LIGHT On Note: For Delay Stop, the unit must be in the On position. Note: For Delay Start, the unit must be in the Off position. To adjust timer setting, tap or hold the UP arrow( ) or the DOWN arrow( ) to change delay timer at .5 hour increments, up to 10 hours, then at 1 hour increments up to 24 hours. The control will count down the time remaining until start (8, 7.5, 7, etc.). The Delay Start mode automatically selects cooling with maximum Fan Speed. The temperature maintained will be the same as previously set. To change the set temperature, press “COOL” then Up or Down arrows until the desired temperature is indicated on the display. After 5 seconds, the control will automatically change the display back to the hours remaining until the unit will start/stop. Turning the unit “ON” or “OFF” at any time will cancel the Delay Start/Stop function. The Delay Start/Stop Feature will work until the unit either starts or stops. Once that happens the above steps have to be repeated again. .. .. 0.5 .. 72 .. 8.5 DO THIS: PRESS SLEEP BUTTON .. .. 88 88 Note: In this “MODE” the selected temperature will increase by 2 degrees F 30 minutes after the mode is selected. The temperature will then increase by another 2 degrees F after an additional 30 minutes. This new temperature will be maintained for 7 hours before it returns to the originally selected temperature. This ends the “Sleep” MODE and the unit will continue to operate as originally programmed. The “Sleep” MODE program can be cancelled at any time during operation by again pressing the “Sleep” button. SLEEP FEATURE: YOU WILL SEE: LIGHT On THEN DO THIS: PRESS TEMP/TIMER BUTTON .. .. .. .. .. 9 Air Conditioner Features (continued) CHECK FILTER FEATURE: YOU WILL SEE: LIGHT On CLEAN AIR FEATURE (on some models): LIGHT On YOU WILL SEE: DO THIS: DO THIS: PRESS CLEAN AFTER CLEANING PRESS CHECK FILTER BUTTON AIR BUTTON Note: This feature is a reminder to clean the Air Filter (See Care and Cleaning) for more efficient operation. The LED (light) will illuminate after 250 hours of operation. To reset after cleaning the filter, press the “Check Filter” button and the light will go off. Note: When this feature is “ON”, the electronic air purifier is energized to remove pollen and impurities from the air. To cancel this feature, press the Clean Air button (the LIGHT will turn off). LIGHT pulsing On & Off intermittently. ON OFF SET TEMP. FAN SPEED Mode En ergy S aver Sleep Ligh t Clock Can cel Timer Fan Reset Lock F C leanAir Foll owMe REMOTE SENSING/FOLLOW ME FEATURE (on some models) : DO THIS: PRESS REMOTE SENSING/FOLLOW ME BUTTON ON NOTE: Remote display is actual temperature at remote control only. ON OFF SET TEMP. FAN SPEED Mode E nergySave r Sle ep Light Clock Cancel Timer Fa n Reset Lock F Clean Air Fol low Me Note: This feature can be activated from the remote control ONLY, the unit must be in a cooling mode. To activate the remote sensing feature, point the remote control towards the unit and press the remote sensing button. Next, use the buttons to set the desired temperature at the remote. (Note that the set temperature will only be displayed on the unit itself). The LIGHT on the unit control will pulse to indicate it received the signal. The LIGHT on the remote control will pulse each time it sends a signal. It will con-tinue to send this signal until the feature is deactivated by pressing the remote sensing button. If the unit does not receive the remote sensingsignal during any 3 minute interval, the unit will beep to indicate the remote sensing mode has ended. The display on the remote control indicates the temperature at the remote ONLY. The unit display indicates the set temperature. Note: Unit display shows “set” temperature.. Air Conditioner Features (continued) FAULT CODES: WARNING CODES: .. If the display reads “AS” or “ED”, In the fan mode if “LO” or “HI” is displayed, a sensor has failed. Contact your this means the room temperature is outside Authorized Frigidaire Service Center. the unit set points of 99oF/37oC (HI) or 32oF/0oC (LO). .. TO TURN UNIT OFF: YOU WILL SEE. .. DO THIS: PRESS ON/ OFF BUTTON .. 10 Air Conditioner Features (continued) ADDITIONAL THINGS YOU SHOUL...