Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
“A" REMOTE CONTROL FOR HEAT MODELS ON/OFF LIGHT HEAT MODE AUTO COOL Fig. “B’! REMOTE CONTROL w/DISPLAY & REMOTE SENSING BUTTON ON/OFF LIGHT MODES AUTO COOL REMOTE CONTROL Fig. “C’! Battery Size: AA Warning: do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries. NOTE: The following instructions represent the Touch Pad, the same instructions can be used for the Remote Control. TO TURN UNIT ON: YOU WILLSEE: 5 SZ000705(En)-YaoKong 5 1 09/2/2005,2:20 PM A n Air Conditioner Features (continued) TO CHANGE TEMPERATURE SETTING: YOU WILL SEE: Note: Tap or hold either up(^) or down (▼) button until the desired temperature is seen on the display. This temperature will be automatically maintained anywhere between 60°F(16°C) and 90°F (32°C) forcooling mode. The temperature will be automatically maintained anywhere between 55°F (13°C) and 80°F (27°C) for heating mode. Ifyou want the display to read the actual room temperature. See “To Operate on Fan Only” section on Page 7. TO ADJUST FAN SPEEDS: YOU WILL SEE (10-99): 4- DO THIS: PRESS TO SELECT: FASTER SLOWER A 2 Digit Display is used to indicate the Fan Speed setting, from 10 through 99. When the “SLOWER” button is pressed the motor speed will slow down at various intervals, down to a minimum setting of 10. To speed the motor up, press the “FASTER” button. The speed will increase at multiple intervals to a maximum setting of 99. Display will revert back to temperature setting after a short time. TO USE AUTO COOL FEATURE: YOU WILL SEE: Note: Fan speed starts at High Speed and adjusts to a slower speed as the room temperature dictates. For example if the room doesn't get too warm, it will stay at the slowest speed. If the room temperature rises quickly, such as a door being opened, it will automatically go to the highest speed. The fan speeds will re-adjust back to the slowest speed as the room returns to the original set temperature. 6 SZ000302(En)-YaoKong(1018) 6 10/25/2004, 2:33 PM n Air Conditioner Features (continued) TO OPERATE ON FAN ONLY: LIGHT On YOU WILL SEE: Note: Use this function only when cooling is not desired, such as for room air circulation or to exhaust stale air. (Remember to open the vent during this function, but keep it closed during cooling for maximum cooling efficiency.) You can choose any fan speed you prefer. (Except “Auto Temp”). During this function, the display will show the actual room temperature, not the set temperature as in the cooling mode. TO USE THE ENERGY SAVER FEATURE: LIGHT On YOU WILL SEE: Note: In this mode, the fan will continue to run for another 3 minutes after the compressor shuts off. The fan then cycles on for 2 minutes at 10 minute intervals until the room temperature is above the set temperature, at which time the the cooling system turns back on. TIMER: DELAY START/STOP FEATURE: LIGHT On YOU WILL SEE: Note 1: For Delay Stop, the unit must be in the On position. Note 2: For Delay Start, the unit must be in the Off position. First, PRESS TIME BUTTON Then to adjust timer setting, tap or hold the UP arrow () or the DOWN arrow ( ,mr ) to change delay timer at .5 hour increments, up to 10 hours, then by 1 hour increments up to 24 hours. The control will count down the time remaining until start (8, 7.5, 7, etc.). The Delay Start mode automatically selects cooling with maximum Fan Speed. The temperature maintained will be the same as previously set. To change the set temperature, press “COOL” then Up or Down arrows until the desired temperature is indicated on the display. After 5 seconds, the control will automatically change the display back to the hours remaining until the unitwill start/stop. PRESSING the unit On/Off button at any time will cancel the Delay Start/Stop function. The Delay Start/Stop Feature will work until the unit either starts or stops. Once that happens he above steps have to be repeated again. 7 SZ000302(En)-YaoKong(1018) 6 4 10/25/2004, 2:33 PM n Air Conditioner Features (continued) CHECK FILTER FEATURE: YOU WILL SEE: LIGHT On Note: This feature is a reminder to clean the Air Filter (See Care and Cleaning) for more efficient operation and cooling. The LED (light) will illuminate after 250 hours of operation. To reset after cleaning the filter, press the “Check Filter"' button and the light will go off. Note: When this feature is “ON”, the electronic air purifier is energized to remove pollen and impurities from the air. To cancel this feature, press the Clean Air button (the LIGHT will turn off). Note: This feature can be activated on the unit touchpad ONLY. SLEEP FEATURE: DO THIS: PRESS SLEEP BUTTON YOU WILL SEE: LIGHT On Note: lnthis“MODE” the set temperature will increase by2 degrees F 30 minutes after the mode is selected. Thetemperature will then increase by another 2 degrees F after an additional 30 minutes. This new temperature will be maintained for 7 hours bef...