Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
• Extend the shutter from the shutter frame and slide it into the shutter tabs on the side channel of the air conditioner, as shown in Fig. 4. • Slide the shutters into the top (“L” Shaped) and bottom (“U” Shaped) channels. The shutters are identified (on frame) as left and right. 3/8” screws “L” shapedmounting bracket “U” shaped Channel(Factory Installed)Fig. 3 Slide down into tabs Shutter tabs Shutter Shutter frame Fig. 4 4 INSTALLATION (cont’d) INSTALLATION INSTRUCTIONS (cont’d) 3) Completing the Installation • Cut the foam (non adhesive) sealing strip to fit the area of the window sill that the air conditioner will rest on. • Carefully place the air conditioner into the window with the “L” shaped mounting bracket (on top) positioned in front of the upper window sash. The bottom of the cabinet should be positioned on the “recessed” portion of the window frame. Pull the window down until it rests just behind the front flange of the (top) “L” shaped mounting bracket (See Fig. 5). • Expand the shutter frames (fully) on each side and secure the top of the frames to the window sash using one 3/4” screw on each side and one in the “L” shaped mounting bracket (Fig. 5). • Secure the shutter clamp on each side of the (lower) shutter and secure to window sill using one 3/4” screw on each side (Fig. 5). • Place the second foam sealing strip to fit the opening between the inside and outside windows, then attach the safety lock to the outside window frame using one 3/4” screw (See Fig. 6). Window sash “L” ShapedMountingBracket Shutter clamps 3/4” screws Fig. 5 Safety Lock 3/4” screw Foam Seal Fig. 6 PLEASE NOTE: Window applications come in a variety of different styles. Therefore, it may be necessary to modify or improvise your particular installation. 5 OPERATING INSTRUCTIONS KEY PAD FEATURES LED DISPLAY: Displays the following information independently;Set Temperature, Ambient RoomTemperature and Auto Timer On/Off settings. POWER: Turns unit On/Off. MODE: Allows you to scroll through and select the desired operating mode; Cool , Dry , Fan Only and *Auto .The selected mode will be denoted by the adjacent indicator light.*‘Auto’is a pre-set factory program that automatically defines the mode (Cool or Dry) and fan speed based on the set temperature FAN SPEED: Select from four different fan settings;Low , Medium , High and Auto during Cool and Fan Only mode. Please note: During ‘Dry’ mode the fan speed is automatically defined . ENERGY SAVER: Automatically cycles the fan on and off while the compressor is not in use. TEMP / TIMER CONTROL: Used to increase or decrease the Temperature setting in 1°C / °F increments, and Auto-Timer On/Off settings in 30min./1hr. increments. Note: This appliance allows you select the temperature scale to be displayed in either “Celsius” or Fahrenheit” according to your preference.To change the temperature scale displayed on the electronic display, press both the “Temp/Timer”adjust arrows simultaneously to alternate between “Celsius”&“Fahrenheit”. CHECK FILTER: The adjacent indicator light will illuminate as a reminder to clean the air conditioner filter (see page 9) Once the filter has been cleaned and replaced, depress the Check Filter button in order to resume operation. SLEEP MODE: When activated, the current set temperature is gradually increased over a one (1) hour period then maintained for seven (7) hours. Once the program is complete, the air conditioner will resume to its previous set temperature (before sleep mode was activated). This feature is mean to be used during the night time hours to prevent the room from getting too cold (while you sleep) and results in less compressor running time and reduced energy consumption. Sleep mode may be cancelled by depressing the Sleep Mode button while the program is running. AUTO-TIMER: Used to initiate the Auto On/ Auto Off timer. Temp/TimerControl Check Filter Mode Selector EnergySaver LED DISPLAY Auto Timer SleepMode Fan Speed Power Button While the Air Conditioner is off (Auto-On): 1) Press the Auto-Timer button once and the adjacent Auto-On indicator light will illuminate. 2) Use the Temp/Timer control cursors to select a delayed On time of up to 24 hours. 3) Select the appropriate mode under which you want the unit to operate (Auto-Cool-Dry-Fan Only) 4) Select the fan speed setting. 5) The time you selected will appear in the LED display. While the Air Conditioner is on (Auto-Off): 1) Press the Auto-Timer button twice and the adjacent Auto-Off indicator light will illuminate. 2) Use the Temp/Timer control cursors to select a delayed Off time of up to 24 hours. 3) The time you selected will appear in the LED display. The Auto On and Auto Off timer can operate during the same program by defining the Auto-Off parameters immediately after the Auto On parameters. The Auto-Timer may be cancelled at any time by turning the unit On/Off. 6 OPERATING INSTRUCTIONS REMOTE CONTROL FEATURES Electronic Display: Displays the following information: A:...