Votos - 2, Puntuación media: 5
(
)
)
|
Resumen del manual
• Be sure to use an exclusive power source. • Contact service man for replacement of power cord. 4 • Step 1 - Prepare Components For Installation Parts for installation are as follows; • SCREW TYPE • Sill Bracket (2 pieces) • Window Kit Left side (Frame ‘L+Shutter) - (1 piece) • Window Kit Right side (Frame ‘R+Shutter) - (1 piece) • Sash Bracket (1 piece) • Frame Guide Lower - (2 pieces) • Levelling Screw (Machine M8x45) - (2 pieces) • 11/4 inch Screw (M5x30) - (4 pieces) • 5/8 inch Screw - (M4x16) - (8 pieces) • 1/4 inch Screw (M4x6) - (8 pieces) • Window Seal A, B (2 pieces) Type A Type B Type C Type D SHAPE SPEC M8 x 45 M5 x 30 M4 x 16 M4 x 6 Q'TY 2 4 8 8 Window Shutter (2 pieces) Window Seal B (1 piece) Sill Bracket (2 pieces) Frame Guide Lower (2 pieces) Window kit Frame Window kit Frame Left side (1 piece) Right side (1 piece) • Step 2 - Prepare Window For Installation 1. Inspect window track, sash and sill to be sure they are strong enough to hold an air conditioner. 2. Measure width between window frame to be sure instant mount will fit in the window. Instant mount models are designed for Windows 24 inch (610mm) to 36 inch (914mm) wide. 3. Mark the center of Window sill with pencil. 4. Insert Screws (Type A) into the sill bracket. 5. Attach Sill bracket to window sill using two Screws (Type B) by each bracket. The outside edge of window bracket should be 9.4 inch (240mm) from center line. 6. Adjust Screw (Type A) so that Sill Bracket have a slight tilt by using carpenter's level meter. Sash Bracket (1 piece) Window Seal A (1 piece) Screw Type B SILL Screw Type A SILL BRACKET 480mm SASH 240mm 610~914mm • Step 3 - Preparation of Chassis 1. Pull the Air-filter out of the Front Grille. 2. Loosen screw which fasten Front Grille with driver. 3. Pull knobs out of the control. (when the knobs are too tight to release, leave them.) 5 6 4. Disassemble Front Grille from Chassis. – Front Grille and chassis are fixed with snap-fit. 1) Release right-lower snap-fit. – Push the right lower side of chassis to the left, with pushing left side of Front Grille to the right until the snap-fit is released. 2) Release left-lower snap-fit. – Push the left-lower side of chassis to the right, with pushing right side of Front Grille to the right until the snap-fit is released. 3) Pull lower side of the Front Grille until it is separated from the chassis. (when knobe remain, pull Front Grille until knobs are released from control) 4) Push base side of the Front Grille to upper side until it is separated from the chassis. 5. After front grille is removed, remove two screws located in both side of chassis and pull out the unit from chassis. Push Push Push Push • Step 4 - Placing Chassis 1. Insert narrow side of ‘Frame Guide Lower’ to rectangle holes located in bottom of chassis, and fasten it with Screw (Type D). 2. Insert Window Kit Frames to Top Guide and Lower Guide. 3. Fasten Shutter to side holes of Chassis with six Screws (Type D). 4. Place the chassis on the wi...
Otros modelos de este manual:Los acondicionadores de aire - DWC-072C (172.1 kb)
Los acondicionadores de aire - DWC-072C (172.1 kb)
Los acondicionadores de aire - DWC-073C (172.1 kb)
Los acondicionadores de aire - DWC-073C (172.1 kb)