Votos - 2, Puntuación media: 3.5 ( )

Fabricar: Bryant Tamaño del archivo: 1.14 mb Nombre del archivo: Idioma del manual:

S Press the On/Off button to start the unit. -- The unit will start in the last operating mode and set point. The ON/OFF indicator will appear. S Press button On/Off to stop the unit. -- All indicator lights on the unit will go out, and the remote control will display the set point, mode and time. NOTE: If the On/Off button is pressed too soon after a stop, the compressor will not start for 3 minutes due to the inherent protection against frequent compressor cycling. The unit will only emit an audible beep when the signals are received correctly. Selecting an Operating Mode Use the Operating Mode button to select one of the available modes. SET TEMP. C L O C K SPEED AUTO OPERATING MODE AUTO COOL DR Y HE AT FAN AUTO COOL DRY HEAT FAN A08034 / A07548 Setting the Room Temperature Set Point Pressing the increase temperature set point and decrease buttons will raise or lower the temperature. The unit will confirm signal receipt with a beep and the value of the set temperature on the display will change accordingly. The temperature can be set between 62_F (17_C) and 88_F (31_C). NOTE: In Cooling mode, if the temperate selected is higher than the room temperature, the unit will not start. The same applies for the Heating mode if the selected temperature is lower than the room temperature. 7 Selecting the Fan Speed SET TEMP. C L O C K SPEED AUTO AUTO LOW MED HIGH A08036 The fan speed can be selected by pressing the FAN SPEED button. NOTE:When the unit is on, the fan will run continuously in cooling or heating. When in heating, there might be situations where the fan will slow down or shut off to prevent cold blow. Selecting the Horizontal Direction Louver Position In order to optimize comfort, the horizontal louver will operate in a preset range as shown in the figure below. COOLING HEATING A08044 The horizontal louvers can be adjusted using the remote control and can be set to be stationary or moving continuously. Air Direction Press the AIR DIRECTION button repeatedly to choose one of the louver positions. Every time the air direction button is pushed, the louver will swing by 6 degrees. In the Cooling, Dehumidification, and Fan Only mode, the louver will swing in the cooling range. In the Heating mode, the louver will swing in the heating range. NOTE: Always use the remote control to adjust the louver position, otherwise abnormal operation may occur. If the louver is manually adjusted out of its range, turn the unit off and then on again. Auto Swing To have the louver moving continuously, push the SWING button. Push again to stop the louver. Selecting Vertical Direction of the Louver The vertical louvers can be adjusted manually to direct the airflow to achieve the optimal comfort in the space. A07543 Timer Function TIMER ON (to start the unit) and TIMER OFF (to stop the unit) can be used separately or together. Timer ON only SET TEMP. C L O C K SPEED AUTO AUTO TIMER ON A08037 This function will allow the unit to start automatically at the set time. The TIMER ON can be set while the unit is on or off. UNIT ON -- Press the TIMER button once. The current time flashes next to the TIMER ON display on screen. Press the temp Y button or temp B button to set the desired “TIME ON”. Every time the Y or B button is pushed, the time increases or decreases by 10 minutes. -- When the TIMER ON is set, the TIMER light on unit illuminates. The unit will shut off and will start again at the set time. UNIT OFF -- Set the timer described in the UNIT ON section. -- The unit will start at the set time. To cancel TIMER setting, press the CANCEL button. Timer OFF only SET TEMP. C L O C K SPEED AUTO AUTO TIMER OFF A08040 This function will allow the unit to stop automatically at the set time. The timer can be set while the unit is on or while it is off. UNIT ON -- Press the TIMER button twice. The current time flashes next to the TIMER OFF display on screen. Press the temp Y button or temp B button to set the desired “TIME OFF”. Every time the Y or B button is pushed, the time increases or decreases by 10 minutes. -- When the TIMER OFF is set, the timer light on the unit illuminates and the unit turns off automatically at the set time. UNIT OFF -- Set the TIMER off as described in the UNIT ON section. -- The unit will turn on and will turn off at the set time. -- If TIMER OFF is canceled (by pushing the cancel button), before the set time elapses, the unit will continue running. 8 Timer ON and Timer OFF SET TEMP. C L O C K SPEED AUTO AUTO TIMER OFF TIMER ON A08041 Use both functions to program the unit to turn on and shut off at specified times. UNIT OFF -- Set TIMER ON as previously described. -- Set TIMER OFF as previously described. -- The unit will start automatically at the set TIME ON and will turn off at the set TIME OFF. UNIT ON -- Set TIME OFF as previously described. -- Set TIME ON as previously described. -- The unit will turn off automatically at the set TIME OFF and will turn on at the set TIME ON. Sleep Mode This mode is ...

Descargar ahora

Introduzca dos números de la imagen: