Votos - 1, Puntuación media: 5 ( )

Fabricar: GE Tamaño del archivo: 481.9 kb Nombre del archivo: Idioma del manual:

These models should be installed on their own single branch circuit for best performance and to prevent overloading house or apartment wiring circuits, which could cause a possible fire hazard from overheating wires. 9 Consumer Support Troubleshooting Tips Installation Instructions Care and Cleaning Operating Instructions Safety Instructions Installing a J-Model in an existing wall case. Read these instructions completely and carefully. IMPORTANT! GE strongly recommends the removal of the old wall case and the installation of a new GE Wall Case. If you decide to keep the existing wall case, you may need a kit to ensure proper performance. If you DONOT use a kit, you run the risk of poor performance or product failure. This is not covered under the terms of the GE warranty. J-Model Qualifying Questions J-model air conditioners may fit in existing wall cases. However, they often need a kit to properly adapt the case to the GE air conditioner. Answer these questions and see the chart below for the proper kit. C B A What brand air conditioner will you be replacing? What are the dimensions of the wall case currently in use? What is the model number of the chassis currently in use? What is the model (or Type) number of the wall case currently in use? Frequently, the J-model adapter kit will apply to another brand model “series” or specific vintage. In these cases, you need the chassis model number and/or the wall case or “type” number to confirm the use of the correct adapter kit. D What type of outdoor grille is used with the current wall case? There may be an architectural grille attached to a wall case to enhance the exterior appearance of the building. Custom grilles may be used with J-model wall cases provided a J-model adapter kit is also used to ensure proper airflow. 10 Read these instructions completely and carefully. GE Kit Numbers Use GE For: Description: Kit Number: RAK56A100 GE RAB13, 14 & 15 (ACLB & RCL Chassis) Fits all GE wall cases 26. W x 18. H x 24. D RAK107 Hotpoint ACXB10 & 11 (ACTB Chassis) Adapts an older Hotpoint wall case to a “J” model chassis. Fits Hotpoint wall cases 253.4. W x 167.8. H x 185.8. D RAK108 Whirlpool Type 23W Wall Case Adapts Whirlpool wall case to a “J” model chassis. Fits Whirlpool wall cases 257.8. W x 161.2. H x 231.8. D RAK110 GE RAB30 (“F” models) Adapts GE wall case to a “J” model chassis. Fits the RAB 30 wall case 26. W x 18. H x 24. D RAK123 Fedders Wall Case “A” Adapts Fedders wall case to a “J” model chassis. Fits Fedders wall cases 27. W x 163.4. H x 163.4. D RAK126 Westinghouse Wall Case (Type 2626D73H01) Adapts Westinghouse wall case to a “J” model chassis. Fits Westinghouse wall cases 257.8. W x 157.16. H x 16. D RAB46, 47 & 48 Use these kits for all other brands not listed. Standard wall case for “J” model chassis. RAG13 stamped aluminum exterior grille included. Remove the existing case and replace. RAK690 RAB36, 37, 38, 46, 47 or 48 (J-Chassis) If you attach a custom architectural outdoor grille, use this kit to ensure proper airflow. RAG14E RAB36, 37, 38, 46, 47 or 48 (J-Chassis) Architectural louvered exterior grille 11 Safety Instructions Operating Instructions Care and Cleaning Installation Instructions Troubleshooting Tips Consumer Support Consumer Support Troubleshooting Tips Installation Instructions Care and Cleaning Operating Instructions Safety Instructions Installing a J-Model in an existing wall case. Read these instructions completely and carefully. Install the Air Conditioner in the Case. A Remove the locking plate on the front D Reinstall the locking plate with the tab left side. behind the wall case flange. Tighten B C the case. Make sure that the tubing on the G Attach the front grille. An opening for unit does not touch the wall case and that the the power cord is on the bottom of the case installation is secure. front grille. Remove the shipping pad inside the air conditioner next to the compressor. Carefully slide the air conditioner back into the screw. Attach the power cord to the base pan with the clamp. When the wall outlet is to the left, extend the cord under the unit and hold it in place with the clamp. F E REMOVE SHIP PAD!REMOVE TAPE ONVENT LEVER! Locking plate Remove shipping pad Clamp Power cord Power cord Clamp Base pan Remove screw 12 Notes. 13 Safety Instructions Operating Instructions Care and Cleaning Installation Instructions Troubleshooting Tips Consumer Support Before You Call For Service… Consumer Support Troubleshooting Tips Installation Instructions Care and Cleaning Operating Instructions Safety Instructions Troubleshooting Tips Save time and money! Review the chart on this page first and you may not need to call for service. Problem Possible Causes What To Do Air conditioner does not start The air conditioner is unplugged. The fuse is blown/circuit breaker is tripped. Power failure. • Make sure the air conditioner plug is pushed completely into the outlet. • Check the house fuse/circuit brea...

Descargar ahora

Introduzca dos números de la imagen: