Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
(Signal receiving sound: two short beeps or one long beep.) Operation Indication Lamps On/Off : Lights up during the system operation. Filter Sign : Lights up after 2400 hours from the time of first operating unit. (Refer to page 19.) Timer : Lights up during Timer operation. Defrost Mode : Lights up during Defrost Mode or Hot Start operation. (Heat pump model only) Outdoor Unit : Lights up during outdoor unit operation. Operation (Cooling model only) Forced : Operation procedures when the remote control Operation can't be used. Heat pump model: Cassette Type Air Conditioner for cooling and heating Cooling model: Cassette Type Air Conditioner for cooling 6 Name and Function of Remote Controller Timer Cancel Program Week Hour Min Holiday Set/Clr RESET Plasma ZONE 1 2 3 4 Operation unit JET Humidify AUTO AUTO SWING OPERATION FAN SPEED Program set SET TEMP SUB FUNCTION Room Temp HI MED LO Heater Defrost Filter Preheat Out door Time Timer On Set no. Time Off 01 03 05 07 09 11 13 15 17 19 21 23 Remote Controller 3 10 12 14 15 11 13 18 16 2 1 Heat Pump Model Cooling Model 5 4 6 8 9 7 17 Operation display Displays the operation conditions. On/Off Button Operation starts when this button is pressed, and stops when the button is pressed again. Set Temperature Button Used to set the temperature when the desired temperature is obtained. FAN Operation Button Used to circulate room air without cooling or heating. Fan Speed Button Used to set the desired fan speed. Operation Mode Selection Button Used to select the operation mode. • Auto Operation Mode • Cooling Operation Mode • Soft Dry Operation Mode • Heating Operation Mode(except cooling model) Auto Swing Button Used to swing up and down. Room Temperature Checking Button Used to check the room temperature. Plasma Air Clean Button (optional) Timer Cancel Button Used to cancel the timer. Timer Set Button Used to set the timer when the desired time is obtained. Week Button Used to set a day of the week. Program Button Used to set the weekly timer. Holiday Button Used to set a holiday of the week. Time Set Button Used to set the time of the day and change the time in the weekly timer Function. Set and Clear Button Used to set and clear the weekly timer. Jet Cool Button Used to select jet cool mode. Reset Button Used to set the current time and clear the setting time. 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 . Display temperature can be different from actual room temperature if the remote controller is installed at the place where sun-rays are falling directly or the place nearby heat source. Wireless Remote Controller (optional) This air-conditioner is equipped with wired remote controller basically. But if you want to be available with wireless remote controller, you pay for it. Signal transmitter (Transmits the signals to the signal receptor) ON OFF SET CANCEL PLASMA 1 7 12 3 2 13 4 8 5 9 6 10 Heat Pump 14 15 Model 11 Cooling Model Flip-up door (opened) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 OPERATION DISPLAY Displays the operation conditions. ON/OFF BUTTON Operation starts when this button is pressed and stops when the button is pressed again. JET COOL BUTTON Used to select jet cool mode. ON/OFF TIMER BUTTONS Used to set the time of starting and stopping operation. TIME SETTING BUTTONS Used to adjust the time. TIMER SET/CANCEL BUTTONS Used to set the timer when the desired time is obtained and to cancel the Timer operation. AIR SWING BUTTON Used to swing up and down. SLEEP MODE BUTTON Used to set Sleep Mode Auto operation. AIR CIRCULATION BUTTON Used to circulate the room air without cooling or heating (turns indoor fan on/off). ROOM TEMPERATURE CHECKING BUTTON Used to check the room temperature. RESET BUTTON Used prior to resetting time or after replacing batteries. INDOOR FAN SPEED SELECTOR Used to select fan speed in four steps-low, medium, high, or CHAOS. ROOM TEMPERATURE SETTING BUTTONS Used to select the room temperature. ORERATION MODE SELECTION BUTTON Used to select the operation mode. PLASMA AIR CLEAN BUTTON(OPTIONAL) ENGLISH CAUTION of handling the Remote Controller • Aim at the signal receptor on the wired remote controller so as to operate. • The remote control signal can be received at a distance of up to about 7m. • Be sure that there are no obstructions between the remote controller and the signal receptor. • Do not drop or throw the remote controller. • Do not place the remote controller in a location exposed to direct sunlight, or near the heating unit, or any other heat source. • Block a strong light over the signal receptor with a curtain or etc. so as to prevent the abnormal operation. (ex:electronic quick start, ELBA, inverter type fluorescent lamp) 7 8 AUTO SWING HI ZONE Operation unit Program set Room Temp MED LO AUTO JET Heater Defrost Filter Preheat Humidify Out door Timer On Set no. Time Off 01 03 05 07 09 11 13 15 17 19 21 23 1 2 3 4 OPERATION SET TEMP FAN SPEED SUB FUNCTION Time AUTO SWING HI ZONE Operation unit Program set Room Temp MED L...
Otros modelos de este manual:Los acondicionadores de aire - LT-E1862RL (13.06 mb)
Los acondicionadores de aire - LTUE2460HL (13.06 mb)