Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
Secure the case through the case track into the window stool on each side, using two 1. screws. Secure to stool 6 Assemble and Attach the Sill and Support Brackets Attach both sill brackets to the window sill using a 1. long screw on each side. Tighten the bolts and nuts on both sides. Loosely attach the sill brackets to the support brackets with 5/8. long carriage bolts and nuts. Find the track hole that aligns with the sill bracket on the outer edge of the window sill. Using the 5/8. long machine screws and nuts attach the support brackets to the case track hole on each side. D C B A Sill bracket Track hole Sill Nut Support bracket Carriage bolt Level NOTE: When finished, use a level to make sure the case tilts to the outside 1/4.minimum. This prevents water from entering the room. 11 Customer ServiceTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions Customer ServiceTroubleshooting TipsOperating InstructionsSafety InstructionsInstallation InstructionsCustomer ServiceTroubleshooting TipsInstallation InstructionsSafety InstructionsOperating InstructionsCustomer Service Troubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions Troubleshooting TipsOperating InstructionsSafety InstructionsInstallation InstructionsCustomer ServiceTroubleshooting TipsInstallation InstructionsSafety InstructionsOperating InstructionsCustomer Service Troubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions Window Installation Instructions 7 Install the Window Filler Panels and Locking Bracket B A Extend the filler panels to fill the window opening. Secure the panels using four 5/8. long screws. Attach the window locking bracket with aC 8 Install the Window Gasket and Replace the Air Conditioner Slide the air conditioner into the case and ground/anti-theft screws removed at the Install the front grille and attach to case using the 2 screws removed previously. Reinstall the air filter to the front grille. Make sure the unit is OFF before inserting cord plug into the outlet. Check all seals and plug any remaining air gaps with a suitable weatherproof caulk. Cut the foam top window gasket to the window width. Stuff the foam between the glass and the window to prevent air and insects from getting into the room. E D BA C 12 Through-the-Wall Installation The case may be installed through-the-wall in both existing and new construction. Read completely, then follow step-by-step. Customer ServiceTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions 1 IMPORTANT: n Any side louvers must project on the outdoor side of the wall. n The room side of the case must project into the room at least1 1/2. from the finished wall. n The case must be installed level from side-to-side and with a1/4. tilt from front to rear. D C B A Remove the air conditioner from the case. For specific instructions, refer to the Window Installation Instructions. Make certain a wall receptacle is available close to the hole location or make arrangements to install a receptacle. Determine the size of wall opening by adding 1/8. to the height and width of the case. Measure height from the top of the case to the bottom of the rail. Place the case in the wall opening and secure the bottom rail, case sides and top with 12 1. long #10 wood screws. NOTE: Drill pilot holes, if necessary, for proper installation. If the frame is oversized, use shims to prevent case distortion. 2 Finish the Wall Opening Caulk all four sides on the outdoor side of the case to prevent moisture from getting through to the interior wall. Use of flashing (drip rail) will further prevent water from dripping inside the wall and down the outside of the building. Caulking Plaster line T rim molding (if desired) Flashing (drip rail) Holes for #10 1 . long wood screws Brick veneer Lintel angle (if required) Caulking 1 1 / 2 . min. Roomside Grounding/anti-theft screw Caulking (between bottom rail and flashing) 13 Before you call for service… Troubleshooting Tips Save time and money! Review the chart below first and you may not need to call for service. Customer ServiceTroubleshooting TipsOperating InstructionsSafety InstructionsInstallation InstructionsCustomer ServiceTroubleshooting TipsInstallation InstructionsSafety InstructionsOperating InstructionsCustomer Service Troubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions Problem Possible Causes What To Do Air conditioner does not start The air conditioner is unplugged. The fuse is blown/circuit breaker is tripped. Power failure. • Make sure the air conditioner plug is pushed completely into the outlet. • Check the house fuse/circuit breaker box and replace the fuse or reset the breaker. • If power failure occurs, turn the mode control to OFF. When power is restored, wait 3 minutes to restart the air conditioner to prevent tripping of the compressor overload. Air conditioner does not cool as it s...