Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
No. Plug Fig. No. HF203G AC C 120V1P 1,900 15.8 6 3 HF203G AC C 240V1P 2,000 8.3 6 4 HF303H AC* C 120V1P 3,000 25.0 7 — HF303G AC C 240V1P 3,000 12.5 7 3 HF403G AC C 240V1P 4,000 16.7 7 5 HF203EG DC E 120V1P 1,900 15.8 9 3 HF203DG DC E 240V1P 2,000 8.3 8 4 HF303E DC* E 120V1P 3,000 25.0 12 — HF303DG DC E 240V1P 3,000 12.5 11 4 HF403E DC** E 240V1P 4,000 16.7 11 — * Cord Only, no plug. ** Without Cord and plug. 12-5/8” 11-3/8” 13-3/16” 1” 8” 9-3/4” Figure 2 Figure 2A GENERAL Hazard of Fire or Discoloration of Temperature Hazard of Electric Shock. Any installation involving Sensitive Fabrics. Keep combustible material and electric heaters must be effectively grounded in such fabrics away from heater. Do not operate accordance with the National Electrical Code. Use heater where flammable vapors, gases or liquids the required polarized wall receptacle that mates are present. Heaters should not be operated in with the appropriate plug, referenced in Table A, room temperatures above 80°F. shown in Figures 3, 4 or 5 (see Page 2). To avoid personal injury read “IMPORTANT INSTRUCTIONS” on page 3 before installation or operation of heater. © 2010 Chromalox®, Inc. WIRING Figure 10. (Consult Table A for actual plug configuration.) No adapter is available for these blade type configurations, and none should be used. Electric Shock Hazard. Heater case must be effec- An appropriate 20A @ 125V, 15A @ 250V or 20A @ 250V tively grounded in accordance with the National grounding outlet must be used. When properly installed, it Electrical Code to avoid hazard of electric shock. provides a ground connection through the cord to the heater to NOTE: All electrical wiring must be installed in accordance with protect the operator from electric shock. the National Electrical Code and local codes by a qualified person. 2. Connect heater according to the voltage and frequency specified on the nameplate and using the appropriate wiring dia1. This heater is for use on 120, 208 or 240 volts. (See heater gram (below). nameplate.) The cord has a plug similar to one shown in Figure 3 NEMA 5-20P 20A 125V Figure 4 NEMA 6-15P 15A 250V Figure 5 NEMA 6-20P 20A 250V Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 Figure 11 Figure 12 MAINTENANCE 2. Following long periods of idleness, heater should be vaccuumed before start-up, to remove accumulated combustible particles which otherwise may smoke or incinerate on initial 1. Hazard of Electric Shock. Disconnect heat up. all power before attempting to service this heater. 3. When heater is not in use, store in safe location to preventDo not attempt to service heater while unit is operating as heater and/or power cord damage. there is hazard of electric shock, injury from operating fan and 4. HF heaters use permanently lubricated motors, do not attemptburns from hot heating elements. to lubricate. IMPORTANT INSTRUCTIONS When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Read all instructions before using this heater. 2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Fire Hazard. Keep electrical cords and combustible materials, such as drapes and other furnishings, away from heater. 3. Extreme caution is necessary when any heater is used by or near children or handicap individuals and whenever the heater is left operating and unattended. 4. Always unplug heater when not in use. 5. Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Return heater to authorized service facility for examination, electrical or mechanical adjustments, or repair. 6. Do not use outdoors. 7. This heater is not intended for use in wet or moist locations. 8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners or the like. Arrange cord away from traffic area and where it will not be tripped over. 9. To disconnect heater, turn controls off, then remove plug from outlet. NOTE: HF303E DC, HF303EG DC and HF403E DC heaters contain an integral fan delay. To de-energize these heaters, turn toggle switch to the off position and allow heater to run until fan stops, then remove plug from outlet. 10. Connect to properly grounded outlets only. 11. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock, fire or damage the heater. 12. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where opening may become blocked. 13. Do not use it in areas where gasoline, paint or flammable liquids are used or stored. 14. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock or injury to persons. 15. This heater is not intended for use with a...