Votos - 4, Puntuación media: 3.5
(
)
)
|
Resumen del manual
a nut or a washer), we would be glad to replace them, or for the sake of expediency, replacements can be obtained at your local hardware store. Figure 1. Parts layout. NOTICE A full parts list and breakdown can be found toward the end of this manual. For easier assembly, or to identify specific parts, please refer to the detailed illustrations at the end of the manual. -6-H2854 1 H.P. Variable Speed Plunge Router SECTION 4: ASSEMBLY Beginning Assembly Handles ! Disconnect power to the machine when performing any maintenance, assembly or adjustments. Failure to do this may result in serious personal injury. Keep loose clothing rolled up and out of the way of machinery and keep hair pulled back. Wear safety glasses during the entire assembly process. Failure to comply may result in serious personal injury. Some metal parts may have sharp edges on them after they are formed. Please examine the edges of all metal parts before handling them. Failure to do so could result in injury. The two handles supplied with your router come unattached from the main unit. You will need to thread them into the mounting holes located on both sides of the upper router base as shown in Figure 2. When you want to store the router in its case, the handles will need to be removed and threaded back into the case mounting locations. NOTICE Be careful not to over-tighten the handles when installing them into the router unit. The threads can become stripped if excessive force is used. Figure 2. Installing handles. Most of your Model H2854 has been assembled at the factory, but some parts must be assembled or installed after delivery. We have organized the assembly process into steps. Please follow along in the order presented here. TOOLS REQUIRED: Phillips® and flat head screw driver, 4mm Allen® wrench (supplied), 19mm open end wrench (supplied). -7 H2854 1 H.P. Variable Speed Plunge Router Installing Bits Disconnect power to the machine when perform- ing any maintenance, assembly or adjust- ments. Failure to do this may result in serious personal injury. ! The Model H2854 is supplied with a 1.4" collet for use with all 1.4" router bits. To install a bit: 1. Remove the collet nut from the spindle shaft using the supplied open-end wrench, while pressing the spindle shaft lock pin. 2. Once the collet nut is removed, you will be able to insert the 1.4" collet into the spindle shaft as shown in Figure 3. 3. Be careful not to let the collet fall onto the floor. Damage to the collet could occur. 4. Press the spindle shaft lock pin and thread the collet nut onto the spindle shaft as shown in Figure 4. The router bit should not be inserted into the collet at this time. Be sure not to cross the threads when starting the col- let nut onto the spindle shaft. Do not tighten the collet nut more than several turns at this time. 5. Insert the shaft of a 1.4" router bit into the col- let. Be sure to follow the router bit manufacturer’s directions regarding how far the bit shaft must be inserted into the collet for safe operation. 6. Once the bit is inserted into the collet, press the spindle shaft lock pin and continue to tighten the collet nut with the supplied open- end collet wrench as shown in Figure 5. NOTICE When the collet nut is removed from the spindle shaft, take care to prevent the collet from dropping onto the floor. The collet may become damaged if it is dropped, causing it to not secure router bits properly. Collet Figure 3. Inserting collet. Figure 4. Threading collet nut onto spindle. Collet Nut Spindle Shaft Lock Pin Figure 5. Tightening bit into router. H2854 1 H.P. Variable Speed Plunge Router -8 Dust Collection Depth Stop The Model H2854 is supplied with a dust collection attachment. Routing produces large amounts of wood dust that can be both damaging to your lungs as well as messy around your worksite. We recommend connecting a vacuum system to the dust collection attachment to keep wood dust to a minimum. Use a tapered hose end to ensure a tight connection to the dust collection attachment. To mount the dust collection attachment to the router base: 1. The dust collection attachment has a long lip on one side and two small lips on the other side. Line up the lips with the slots in the router base and snap into place as shown in Figure 6. 2. Using two Phillips® head screws, secure the dust collection assembly to the base of the router. Figure 6. Installing dust port. The Model H2854 is supplied with both standard and metric depth stops. To attach the depth stop: 1. Loosen the lock knob located on the front of the router base and slide the desired stop into the diamond-shaped slot on the upper base as shown in Figure 7. 2. Tighten the lock knob until the stop is held securely in place. Be sure not to overtighten the knob. Depth adjustment will be discussed later in the manual. Figure 7. Installing depth stop. H2854 1 H.P. Variable Speed Plunge Router -9 SECTION 5: ADJUSTMENTS ! Disconnect power to the machine when performing any ma...