Votos - , Puntuación media:
(
)
)
Fabricar: Harbor Freight Tools
Tamaño del archivo: 325.43 kb
Nombre del archivo: 91959.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
5. Do not alter or adjust any part of the Cultivator that is assembled and supplied by the manufacturer. 6. Always follow and complete scheduled Engine and Cultivator maintenance. BURN AND CHEMICAL PRECAUTIONS 1. Avoid contact with hot fuel, oil, exhaust fumes, and hot solid surfaces. 2. Avoid body contact with fuels, oils, and lubricants used in the Engine. If swallowed, seek medical treatment immediately. Do not induce vomiting if fuel is swallowed. For skin contact, immediately wash with soap and water. For eye contact, immediately flush eyes with clean water. NOISE PRECAUTIONS 1. Prolonged exposure to noise levels above 85 dBA is hazardous to hearing. Always wear ANSI approved ear protection when operating or working around the Cultivator when it is running. HEART PACEMAKER PRECAUTIONS 1. People with pacemakers should consult their physician(s) before using this product. Electromagnetic fields in close proximity to a heart WARNING! pacemaker could cause interference to or failure of the pacemaker. SKU 91959 For technical questions please call 1-800-444-3353 PAGE 7 CALIFORNIA PROPOSITION 65 WARNINGS 1. WARNING! Operation of this Cultivator and/or Engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. (California Health & Safety Code 25249.5, et seq.) OWNER/OPERATOR PRECAUTIONS 1. WARNING! The warnings, precautions, and instructions discussed in this manual cannot cover all possible conditions and situations that may occur. The operator must understand that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. ASSEMBLY INSTRUCTIONS NOTE: For additional references to the parts listed in the following pages, refer to the Assembly Diagram on page 14. 1. Prior to use, the Lower Handle (65) must be attached to the Housing (13). To do so, align the mounting holes at the bottom (on each side) of the Lower Handle with the mounting holes located on each side of the Housing. Then use four Bolts (64), four Washers (26), and four Self-Lock Nuts (27) to secure the Lower Handle to the Housing. (See Figure A.) LOWER HANDLE (65) LOWER HANDLE (65) UPPER HANDLE (66) UPPER HANDLE (66) GRIP HANDLE (67) GRIP HANDLE (67) BOLT (64) WASHER (26) SELF-LOCK NUT (27) BOLT (64) WASHER (26) SELF-LOCK NUT (27) FIGURE A SKU 91959 For technical questions please call 1-800-444-3353 PAGE 8 2. The Upper Handle (66) is folded for shipping purposes. Loosen the Grip Handles (67) located on each side of the Upper Handle. Unfold the Upper Handle to its normal working position. Then, firmly retighten each Grip Handle to secure the Upper Handle in place. (See Figure A.) OPERATING INSTRUCTIONS Pre-Start Checks: 1. IMPORTANT ! Prior to first using the Cultivator, the Engine MUST be filled with a high quality SAE 10W-30 grade engine oil until the level of the oil is indicated as “FULL” on the Oil Dipstick. To do so, unscrew and remove the Oil Dipstick located on the Engine Crankcase. Fill the Engine Crankcase with the Proper amount of oil. Then, screw the Dipstick back into the Oil Fill Hole. (For additional information, refer to the engine manufacturer’s manual.) (See Figure B.) OIL DIPSTICK “FULL” LEVEL INDICATOR LINE ENGINE CRANKCASE FIGURE B 2. Before the first use, remove the Engine’s Fuel Tank Cap and fill the Fuel Tank with unleaded gasoline. Then, replace the Fuel Tank Cap.Thereafter, check the Fuel Tank for the amount of unleaded gasoline. Refill the Fuel Tank onlywith unleaded gasoline. BEWARE of possible buried obstacles such as cable, conduit, and irrigation lines. To Start And OperateThe Cultivator: 1. Move the Cultivator to the position where you wish to begin tilling the soil. 2. If necessary, adjust the Depth Skid (57) in order to till the soil at a desired depth SKU 91959 For technical questions please call 1-800-444-3353 PAGE 9 (to a maximum 11” deep). To do so, remove the two Cotter Pins (39). Remove the two Pin Shafts (38). Raise or lower the Depth Skid (57) to obtain the desired tilling depth. Then, replace the Pin Shafts and Cotter Pins. (See Figure C.) PIN SHAFT (38) PIN SHAFT (38) DEPTH SKID (57) LEFT SIDE VIEW (TO LOWER) (to a maximum 11” deep). To do so, remove the two Cotter Pins (39). Remove the two Pin Shafts (38). Raise or lower the Depth Skid (57) to obtain the desired tilling depth. Then, replace the Pin Shafts and Cotter Pins. (See Figure C.) PIN SHAFT (38) PIN SHAFT (38) DEPTH SKID (57) LEFT SIDE VIEW (TO LOWER) RIGHT SIDE VIEW (TO RAISE) FIGURE C COTTER PIN (39) COTTER PIN (39) DEPTH SKID (57) 3. Open the Fuel Valve on the Engine. 4. Turn the Choke Lever on the Engine to its “CHOKE” position. 5. Set the Throttle Control (71) to its “FAST” position. (See Figure D, next page.) 6. Hold the Start Handle of the Engine loosely and pull it slowly several times to allow the gasoline to flow into the Engine’s carburetor. Then hold the Start Handle firmly and pull the rope har...